Proximity test for connector 10/32, con-10.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 11/32, con-12.
Proximity test for connector 12/32, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 13/32, con-16.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183
Proximity test for connector 14/32, con-17.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 15/32, con-20.
Proximity test for connector 16/32, con-21.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/32, con-22.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 18/32, con-23.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 19/32, con-24.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 20/32, con-25.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 21/32, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 22/32, con-27.
Proximity test for connector 23/32, con-28.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 24/32, con-29.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 25/32, con-30.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 26/32, con-32.
Proximity test for connector 27/32, con-33.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 28/32, con-36.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 29/32, con-37.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 30/32, con-40.
Proximity test for connector 31/32, con-41.
Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644
Proximity test for connector 32/32, con-42.
Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 26
Connector con-2 current dim = 79
Connector con-3 current dim = 26
Connector con-4 current dim = 29
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 29
Connector con-9 current dim = 25
Connector con-10 current dim = 79
Connector con-12 current dim = 4
Connector con-13 current dim = 79
Connector con-16 current dim = 26
Connector con-17 current dim = 79
Connector con-20 current dim = 4
Connector con-21 current dim = 26
Connector con-22 current dim = 79
Connector con-23 current dim = 26
Connector con-24 current dim = 29
Connector con-25 current dim = 26
Connector con-26 current dim = 26
Connector con-27 current dim = 4
Connector con-28 current dim = 29
Connector con-29 current dim = 25
Connector con-30 current dim = 79
Connector con-32 current dim = 4
Connector con-33 current dim = 79
Connector con-36 current dim = 26
Connector con-37 current dim = 79
Connector con-40 current dim = 4
Connector con-41 current dim = 27
Connector con-42 current dim = 33
Domain list has 18 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 8.32899e-05
Number of periodic target domains = 0
Unstructured domain 1 of 18:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 2 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 3 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 4 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 5 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 6 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 7 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 18:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 10 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 11 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 12 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 13 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 14 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 15 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 16 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 17 of 18:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 18 of 18:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 18 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 18 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.137767 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.142891 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 15022, numTets = 49191, (0.135616 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 17357, numTets = 63210, (0.130265 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 19572, numTets = 76518, (0.126678 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 21667, numTets = 89099, (0.126662 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 23641, numTets = 100952, (0.124270 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 25514, numTets = 112199, (0.168090 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 27292, numTets = 122877, (0.139055 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 28966, numTets = 132931, (0.158228 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 30526, numTets = 142297, (0.123676 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 31965, numTets = 150934, (0.089848 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 33232, numTets = 158561, (0.118973 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 34280, numTets = 164901, (0.100920 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 35025, numTets = 169415, (0.097260 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 35422, numTets = 171836, (0.063714 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 35553, numTets = 172636, (0.046555 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 35559, numTets = 172675, (0.051114 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 35559, numTets = 172675, (0.023433 seconds)
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:49:01PM EDT
Run Time: 00 Hours 00 Minutes 14 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:49:01PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 96 / 96 curves to EGADS originals
GMA contains 32 edge groups
GMA contains 18 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:49:14PM EDT
Export Time: 00 Hours 00 Minutes 13 Seconds
Number of command line arguments = 2
Sat Apr 06 2024 10:49:25PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 18 entries.
Quilt quilt-1: edge tolerance = 6.19964e-05
Quilt quilt-2: edge tolerance = 6.19964e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 6.19964e-05
Quilt quilt-5: edge tolerance = 6.19964e-05
Quilt quilt-6: edge tolerance = 6.19964e-05
Quilt quilt-7: edge tolerance = 6.19964e-05
Quilt quilt-8: edge tolerance = 6.19964e-05
Quilt quilt-9: edge tolerance = 8.32899e-05
Quilt quilt-10: edge tolerance = 8.32899e-05
Quilt quilt-11: edge tolerance = 8.32899e-05
Quilt quilt-12: edge tolerance = 8.32899e-05
Quilt quilt-13: edge tolerance = 8.32899e-05
Quilt quilt-14: edge tolerance = 8.32899e-05
Quilt quilt-15: edge tolerance = 8.32899e-05
Quilt quilt-16: edge tolerance = 8.32899e-05
Quilt quilt-17: edge tolerance = 6.19601e-06
Quilt quilt-18: edge tolerance = 6.19601e-06
Maximum DB edge tolerance = 8.32899e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.665798e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 18 entries.
Quilt list has 18 entries.
Original connector list has 32 entries.
Minimum connector length = 0.00316783
Tolerance = 8.32899e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 32 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-12
Max Edge Tol: 8.329e-05 on con-25
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/32, name = con-1
Changing dimension for connector 1/32 from 11 to 4
Checking dimension for connector 2/32, name = con-2
Checking dimension for connector 3/32, name = con-3
Changing dimension for connector 3/32 from 11 to 4
Checking dimension for connector 4/32, name = con-4
Checking dimension for connector 5/32, name = con-5
Changing dimension for connector 5/32 from 11 to 4
Checking dimension for connector 6/32, name = con-6
Changing dimension for connector 6/32 from 11 to 4
Checking dimension for connector 7/32, name = con-7
Changing dimension for connector 7/32 from 11 to 4
Checking dimension for connector 8/32, name = con-8
Checking dimension for connector 9/32, name = con-9
Changing dimension for connector 9/32 from 11 to 4
Checking dimension for connector 10/32, name = con-10
Checking dimension for connector 11/32, name = con-12
Changing dimension for connector 11/32 from 11 to 4
Checking dimension for connector 12/32, name = con-13
Checking dimension for connector 13/32, name = con-16
Changing dimension for connector 13/32 from 11 to 4
Checking dimension for connector 14/32, name = con-17
Checking dimension for connector 15/32, name = con-20
Changing dimension for connector 15/32 from 11 to 4
Checking dimension for connector 16/32, name = con-21
Changing dimension for connector 16/32 from 11 to 4
Checking dimension for connector 17/32, name = con-22
Checking dimension for connector 18/32, name = con-23
Changing dimension for connector 18/32 from 11 to 4
Checking dimension for connector 19/32, name = con-24
Checking dimension for connector 20/32, name = con-25
Changing dimension for connector 20/32 from 11 to 4
Checking dimension for connector 21/32, name = con-26
Changing dimension for connector 21/32 from 11 to 4
Checking dimension for connector 22/32, name = con-27
Changing dimension for connector 22/32 from 11 to 4
Checking dimension for connector 23/32, name = con-28
Checking dimension for connector 24/32, name = con-29
Changing dimension for connector 24/32 from 11 to 4
Checking dimension for connector 25/32, name = con-30
Checking dimension for connector 26/32, name = con-32
Changing dimension for connector 26/32 from 11 to 4
Checking dimension for connector 27/32, name = con-33
Checking dimension for connector 28/32, name = con-36
Changing dimension for connector 28/32 from 11 to 4
Checking dimension for connector 29/32, name = con-37
Checking dimension for connector 30/32, name = con-40
Changing dimension for connector 30/32 from 11 to 4
Checking dimension for connector 31/32, name = con-41
Checking dimension for connector 32/32, name = con-42
Processing spacing values for connector 1/32, name = con-1
Processing spacing values for connector 2/32, name = con-2
Processing spacing values for connector 3/32, name = con-3
Processing spacing values for connector 4/32, name = con-4
Processing spacing values for connector 5/32, name = con-5
Processing spacing values for connector 6/32, name = con-6
Processing spacing values for connector 7/32, name = con-7
Processing spacing values for connector 8/32, name = con-8
Processing spacing values for connector 9/32, name = con-9
Processing spacing values for connector 10/32, name = con-10
Processing spacing values for connector 11/32, name = con-12
Processing spacing values for connector 12/32, name = con-13
Processing spacing values for connector 13/32, name = con-16
Processing spacing values for connector 14/32, name = con-17
Processing spacing values for connector 15/32, name = con-20
Processing spacing values for connector 16/32, name = con-21
Processing spacing values for connector 17/32, name = con-22
Processing spacing values for connector 18/32, name = con-23
Processing spacing values for connector 19/32, name = con-24
Processing spacing values for connector 20/32, name = con-25
Processing spacing values for connector 21/32, name = con-26
Processing spacing values for connector 22/32, name = con-27
Processing spacing values for connector 23/32, name = con-28
Processing spacing values for connector 24/32, name = con-29
Processing spacing values for connector 25/32, name = con-30
Processing spacing values for connector 26/32, name = con-32
Processing spacing values for connector 27/32, name = con-33
Processing spacing values for connector 28/32, name = con-36
Processing spacing values for connector 29/32, name = con-37
Processing spacing values for connector 30/32, name = con-40
Processing spacing values for connector 31/32, name = con-41
Processing spacing values for connector 32/32, name = con-42
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/32, con-1.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 2/32, con-2.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 3/32, con-3.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183
Proximity test for connector 4/32, con-4.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 5/32, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 6/32, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 7/32, con-7.
Proximity test for connector 8/32, con-8.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 9/32, con-9.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 10/32, con-10.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 11/32, con-12.
Proximity test for connector 12/32, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 13/32, con-16.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183
Proximity test for connector 14/32, con-17.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 15/32, con-20.
Proximity test for connector 16/32, con-21.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/32, con-22.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 18/32, con-23.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 19/32, con-24.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 20/32, con-25.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 21/32, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 22/32, con-27.
Proximity test for connector 23/32, con-28.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 24/32, con-29.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 25/32, con-30.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 26/32, con-32.
Proximity test for connector 27/32, con-33.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 28/32, con-36.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 29/32, con-37.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 30/32, con-40.
Proximity test for connector 31/32, con-41.
Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644
Proximity test for connector 32/32, con-42.
Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 26
Connector con-2 current dim = 79
Connector con-3 current dim = 26
Connector con-4 current dim = 29
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 29
Connector con-9 current dim = 25
Connector con-10 current dim = 79
Connector con-12 current dim = 4
Connector con-13 current dim = 79
Connector con-16 current dim = 26
Connector con-17 current dim = 79
Connector con-20 current dim = 4
Connector con-21 current dim = 26
Connector con-22 current dim = 79
Connector con-23 current dim = 26
Connector con-24 current dim = 29
Connector con-25 current dim = 26
Connector con-26 current dim = 26
Connector con-27 current dim = 4
Connector con-28 current dim = 29
Connector con-29 current dim = 25
Connector con-30 current dim = 79
Connector con-32 current dim = 4
Connector con-33 current dim = 79
Connector con-36 current dim = 26
Connector con-37 current dim = 79
Connector con-40 current dim = 4
Connector con-41 current dim = 27
Connector con-42 current dim = 33
Domain list has 18 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 8.32899e-05
Number of periodic target domains = 0
Unstructured domain 1 of 18:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 2 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 3 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 4 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 5 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 6 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 7 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 18:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 10 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 11 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 12 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 13 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 14 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 15 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 16 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 17 of 18:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 18 of 18:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 18 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 18 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.167400 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.149501 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 15024, numTets = 49207, (0.131673 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 17358, numTets = 63220, (0.124709 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 19573, numTets = 76527, (0.138826 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 21668, numTets = 89108, (0.128931 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 23642, numTets = 100961, (0.176582 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 25515, numTets = 112208, (0.149281 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 27293, numTets = 122886, (0.146017 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 28967, numTets = 132940, (0.162493 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 30527, numTets = 142306, (0.102880 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 31966, numTets = 150943, (0.092796 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 33233, numTets = 158570, (0.121511 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 34281, numTets = 164910, (0.116985 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 35026, numTets = 169424, (0.081190 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 35423, numTets = 171845, (0.057239 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 35554, numTets = 172645, (0.041196 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 35560, numTets = 172684, (0.029300 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 35560, numTets = 172684, (0.023707 seconds)
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:49:38PM EDT
Run Time: 00 Hours 00 Minutes 13 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:49:38PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 96 / 96 curves to EGADS originals
GMA contains 32 edge groups
GMA contains 18 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:49:51PM EDT
Export Time: 00 Hours 00 Minutes 13 Seconds
Number of command line arguments = 2
Sat Apr 06 2024 10:50:02PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 18 entries.
Quilt quilt-1: edge tolerance = 6.19964e-05
Quilt quilt-2: edge tolerance = 6.19964e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 6.19964e-05
Quilt quilt-5: edge tolerance = 6.19964e-05
Quilt quilt-6: edge tolerance = 6.19964e-05
Quilt quilt-7: edge tolerance = 6.19964e-05
Quilt quilt-8: edge tolerance = 6.19964e-05
Quilt quilt-9: edge tolerance = 8.32899e-05
Quilt quilt-10: edge tolerance = 8.32899e-05
Quilt quilt-11: edge tolerance = 8.32899e-05
Quilt quilt-12: edge tolerance = 8.32899e-05
Quilt quilt-13: edge tolerance = 8.32899e-05
Quilt quilt-14: edge tolerance = 8.32899e-05
Quilt quilt-15: edge tolerance = 8.32899e-05
Quilt quilt-16: edge tolerance = 8.32899e-05
Quilt quilt-17: edge tolerance = 6.19601e-06
Quilt quilt-18: edge tolerance = 6.19601e-06
Maximum DB edge tolerance = 8.32899e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.665798e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 18 entries.
Quilt list has 18 entries.
Original connector list has 32 entries.
Minimum connector length = 0.00316783
Tolerance = 8.32899e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 32 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-12
Max Edge Tol: 8.329e-05 on con-25
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/32, name = con-1
Changing dimension for connector 1/32 from 11 to 4
Checking dimension for connector 2/32, name = con-2
Checking dimension for connector 3/32, name = con-3
Changing dimension for connector 3/32 from 11 to 4
Checking dimension for connector 4/32, name = con-4
Checking dimension for connector 5/32, name = con-5
Changing dimension for connector 5/32 from 11 to 4
Checking dimension for connector 6/32, name = con-6
Changing dimension for connector 6/32 from 11 to 4
Checking dimension for connector 7/32, name = con-7
Changing dimension for connector 7/32 from 11 to 4
Checking dimension for connector 8/32, name = con-8
Checking dimension for connector 9/32, name = con-9
Changing dimension for connector 9/32 from 11 to 4
Checking dimension for connector 10/32, name = con-10
Checking dimension for connector 11/32, name = con-12
Changing dimension for connector 11/32 from 11 to 4
Checking dimension for connector 12/32, name = con-13
Checking dimension for connector 13/32, name = con-16
Changing dimension for connector 13/32 from 11 to 4
Checking dimension for connector 14/32, name = con-17
Checking dimension for connector 15/32, name = con-20
Changing dimension for connector 15/32 from 11 to 4
Checking dimension for connector 16/32, name = con-21
Changing dimension for connector 16/32 from 11 to 4
Checking dimension for connector 17/32, name = con-22
Checking dimension for connector 18/32, name = con-23
Changing dimension for connector 18/32 from 11 to 4
Checking dimension for connector 19/32, name = con-24
Checking dimension for connector 20/32, name = con-25
Changing dimension for connector 20/32 from 11 to 4
Checking dimension for connector 21/32, name = con-26
Changing dimension for connector 21/32 from 11 to 4
Checking dimension for connector 22/32, name = con-27
Changing dimension for connector 22/32 from 11 to 4
Checking dimension for connector 23/32, name = con-28
Checking dimension for connector 24/32, name = con-29
Changing dimension for connector 24/32 from 11 to 4
Checking dimension for connector 25/32, name = con-30
Checking dimension for connector 26/32, name = con-32
Changing dimension for connector 26/32 from 11 to 4
Checking dimension for connector 27/32, name = con-33
Checking dimension for connector 28/32, name = con-36
Changing dimension for connector 28/32 from 11 to 4
Checking dimension for connector 29/32, name = con-37
Checking dimension for connector 30/32, name = con-40
Changing dimension for connector 30/32 from 11 to 4
Checking dimension for connector 31/32, name = con-41
Checking dimension for connector 32/32, name = con-42
Processing spacing values for connector 1/32, name = con-1
Processing spacing values for connector 2/32, name = con-2
Processing spacing values for connector 3/32, name = con-3
Processing spacing values for connector 4/32, name = con-4
Processing spacing values for connector 5/32, name = con-5
Processing spacing values for connector 6/32, name = con-6
Processing spacing values for connector 7/32, name = con-7
Processing spacing values for connector 8/32, name = con-8
Processing spacing values for connector 9/32, name = con-9
Processing spacing values for connector 10/32, name = con-10
Processing spacing values for connector 11/32, name = con-12
Processing spacing values for connector 12/32, name = con-13
Processing spacing values for connector 13/32, name = con-16
Processing spacing values for connector 14/32, name = con-17
Processing spacing values for connector 15/32, name = con-20
Processing spacing values for connector 16/32, name = con-21
Processing spacing values for connector 17/32, name = con-22
Processing spacing values for connector 18/32, name = con-23
Processing spacing values for connector 19/32, name = con-24
Processing spacing values for connector 20/32, name = con-25
Processing spacing values for connector 21/32, name = con-26
Processing spacing values for connector 22/32, name = con-27
Processing spacing values for connector 23/32, name = con-28
Processing spacing values for connector 24/32, name = con-29
Processing spacing values for connector 25/32, name = con-30
Processing spacing values for connector 26/32, name = con-32
Processing spacing values for connector 27/32, name = con-33
Processing spacing values for connector 28/32, name = con-36
Processing spacing values for connector 29/32, name = con-37
Processing spacing values for connector 30/32, name = con-40
Processing spacing values for connector 31/32, name = con-41
Processing spacing values for connector 32/32, name = con-42
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/32, con-1.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 2/32, con-2.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 3/32, con-3.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183
Proximity test for connector 4/32, con-4.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 5/32, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 6/32, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 7/32, con-7.
Proximity test for connector 8/32, con-8.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 9/32, con-9.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 10/32, con-10.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 11/32, con-12.
Proximity test for connector 12/32, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 13/32, con-16.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183
Proximity test for connector 14/32, con-17.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 15/32, con-20.
Proximity test for connector 16/32, con-21.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/32, con-22.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 18/32, con-23.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 19/32, con-24.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 20/32, con-25.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 21/32, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 22/32, con-27.
Proximity test for connector 23/32, con-28.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 24/32, con-29.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 25/32, con-30.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 26/32, con-32.
Proximity test for connector 27/32, con-33.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 28/32, con-36.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273
Proximity test for connector 29/32, con-37.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 30/32, con-40.
Proximity test for connector 31/32, con-41.
Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644
Proximity test for connector 32/32, con-42.
Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 26
Connector con-2 current dim = 79
Connector con-3 current dim = 26
Connector con-4 current dim = 29
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 29
Connector con-9 current dim = 25
Connector con-10 current dim = 79
Connector con-12 current dim = 4
Connector con-13 current dim = 79
Connector con-16 current dim = 26
Connector con-17 current dim = 79
Connector con-20 current dim = 4
Connector con-21 current dim = 26
Connector con-22 current dim = 79
Connector con-23 current dim = 26
Connector con-24 current dim = 29
Connector con-25 current dim = 26
Connector con-26 current dim = 26
Connector con-27 current dim = 4
Connector con-28 current dim = 29
Connector con-29 current dim = 25
Connector con-30 current dim = 79
Connector con-32 current dim = 4
Connector con-33 current dim = 79
Connector con-36 current dim = 26
Connector con-37 current dim = 79
Connector con-40 current dim = 4
Connector con-41 current dim = 27
Connector con-42 current dim = 33
Domain list has 18 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 8.32899e-05
Number of periodic target domains = 0
Unstructured domain 1 of 18:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 2 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 3 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 4 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 5 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 6 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 7 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 18:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 18:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 10 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 11 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 12 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 13 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 14 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 15 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 16 of 18:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 17 of 18:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 18 of 18:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 18 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 18 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.148410 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.177093 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 15022, numTets = 49194, (0.160946 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 17355, numTets = 63200, (0.161711 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 19568, numTets = 76495, (0.159525 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 21662, numTets = 89070, (0.148363 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 23636, numTets = 100923, (0.145007 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 25509, numTets = 112170, (0.141965 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 27287, numTets = 122848, (0.134251 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 28961, numTets = 132902, (0.123433 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 30521, numTets = 142268, (0.093286 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 31960, numTets = 150905, (0.143352 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 33227, numTets = 158532, (0.124371 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 34275, numTets = 164872, (0.117114 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 35020, numTets = 169386, (0.095171 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 35417, numTets = 171807, (0.080478 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 35548, numTets = 172607, (0.056295 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 35554, numTets = 172646, (0.036805 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 35554, numTets = 172646, (0.033102 seconds)
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:50:14PM EDT
Run Time: 00 Hours 00 Minutes 12 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:50:14PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 96 / 96 curves to EGADS originals
GMA contains 32 edge groups
GMA contains 18 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:50:27PM EDT
Export Time: 00 Hours 00 Minutes 13 Seconds
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Volume mesh:
Number of nodes = 59386
Number of elements = 340324
Number of triangles = 13638
Number of quadrilatarals = 0
Number of tetrahedrals = 340324
Number of pyramids = 0
Number of prisms = 0
Number of hexahedrals = 0
Body = 1
Number of nodes = 2848
Number of elements = 5692
Number of tris = 5692
Number of quad = 0
Body = 2
Number of nodes = 2825
Number of elements = 5646
Number of tris = 5646
Number of quad = 0
Body = 3
Number of nodes = 1152
Number of elements = 2300
Number of tris = 2300
Number of quad = 0
Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_1.dat ....
Finished writing TECPLOT file
Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_2.dat ....
Finished writing TECPLOT file
Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_3.dat ....
Finished writing TECPLOT file
Writing TECPLOT file: pyCAPS_Pointwise_Test.dat ....
Finished writing TECPLOT file
WARNING: 'capsProblem.__init__' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsProblem.loadCAPS' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsGeometry.__init__' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsProblem.loadAIM' is deprecated. Please use 'Problem.analysis.create'!
WARNING: 'capsAnalysis.__init__' is deprecated. Please use 'Problem.analysis.create'!
WARNING: 'capsAnalysis.setAnalysisVal' is deprecated. Please use 'Analysis.input["varname"].value'!
WARNING: 'capsProblem.closeCAPS' is deprecated. Please use 'close'!
real 16m21.815s
user 13m39.973s
sys 1m27.609s
+ status=0
+ set +x
=================================================
Legacy CAPS verification (using pyCAPS) case pointwise_PyTest.py passed (as expected)
=================================================
=================================================
+ rm -rf pointwise_Symmetry_PyTest
+ echo 'pointwise_Symmetry_PyTest.py test;'
+ tee -a /jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/regressionTest/pyCAPSlog.txt
pointwise_Symmetry_PyTest.py test;
+ python -u pointwise_Symmetry_PyTest.py -verbosity=0 -workDir=runDirectory
+ tee -a /jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/regressionTest/pyCAPSlog.txt
Mapping capsGroup attributes ................
Number of unique capsGroup attributes = 4
Name = Farfield, index = 1
Name = Symmetry, index = 2
Name = Wing1, index = 3
Name = Wing2, index = 4
Mapping capsMesh attributes ................
Number of unique capsMesh attributes = 4
Name = Farfield, index = 1
Name = Symmetry, index = 2
Name = Wing1, index = 3
Name = Wing2, index = 4
Getting mesh sizing parameters
Mesh sizing name - Wing2
Done getting mesh sizing parameters
Writing global Glyph inputs...
Writing egads file '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/pyCAPS/pointwise_Symmetry_PyTest/Scratch/runDirectory_PointwiseSymmetryAnalysisTest_pointwiseAIM/caps.egads'....
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Number of command line arguments = 2
Sat Apr 06 2024 10:52:21PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 14 entries.
Quilt quilt-1: edge tolerance = 5e-07
Quilt quilt-2: edge tolerance = 8.32899e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 8.32899e-05
Quilt quilt-5: edge tolerance = 8.32899e-05
Quilt quilt-6: edge tolerance = 8.32899e-05
Quilt quilt-7: edge tolerance = 9.65124e-05
Quilt quilt-8: edge tolerance = 9.65124e-05
Quilt quilt-9: edge tolerance = 9.65124e-05
Quilt quilt-10: edge tolerance = 5e-07
Quilt quilt-11: edge tolerance = 5e-07
Quilt quilt-12: edge tolerance = 5e-07
Quilt quilt-13: edge tolerance = 9.65124e-05
Quilt quilt-14: edge tolerance = 5e-07
Maximum DB edge tolerance = 9.65124e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 14 entries.
Quilt list has 14 entries.
Original connector list has 30 entries.
Minimum connector length = 0.00316783
Tolerance = 9.65124e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 30 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-1
Max Edge Tol: 9.651e-05 on con-19
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/30, name = con-1
Changing dimension for connector 1/30 from 11 to 5
Checking dimension for connector 2/30, name = con-2
Checking dimension for connector 3/30, name = con-3
Changing dimension for connector 3/30 from 11 to 5
Checking dimension for connector 4/30, name = con-4
Checking dimension for connector 5/30, name = con-5
Changing dimension for connector 5/30 from 11 to 4
Checking dimension for connector 6/30, name = con-6
Changing dimension for connector 6/30 from 11 to 4
Checking dimension for connector 7/30, name = con-7
Changing dimension for connector 7/30 from 11 to 4
Checking dimension for connector 8/30, name = con-8
Changing dimension for connector 8/30 from 11 to 4
Checking dimension for connector 9/30, name = con-9
Changing dimension for connector 9/30 from 11 to 4
Checking dimension for connector 10/30, name = con-10
Changing dimension for connector 10/30 from 11 to 4
Checking dimension for connector 11/30, name = con-11
Checking dimension for connector 12/30, name = con-12
Changing dimension for connector 12/30 from 11 to 4
Checking dimension for connector 13/30, name = con-13
Checking dimension for connector 14/30, name = con-15
Changing dimension for connector 14/30 from 11 to 4
Checking dimension for connector 15/30, name = con-16
Checking dimension for connector 16/30, name = con-18
Changing dimension for connector 16/30 from 11 to 4
Checking dimension for connector 17/30, name = con-19
Checking dimension for connector 18/30, name = con-20
Changing dimension for connector 18/30 from 11 to 4
Checking dimension for connector 19/30, name = con-21
Checking dimension for connector 20/30, name = con-23
Changing dimension for connector 20/30 from 11 to 4
Checking dimension for connector 21/30, name = con-24
Checking dimension for connector 22/30, name = con-26
Changing dimension for connector 22/30 from 11 to 4
Checking dimension for connector 23/30, name = con-27
Checking dimension for connector 24/30, name = con-28
Changing dimension for connector 24/30 from 11 to 5
Checking dimension for connector 25/30, name = con-29
Checking dimension for connector 26/30, name = con-30
Changing dimension for connector 26/30 from 11 to 5
Checking dimension for connector 27/30, name = con-31
Checking dimension for connector 28/30, name = con-33
Checking dimension for connector 29/30, name = con-35
Checking dimension for connector 30/30, name = con-37
Processing spacing values for connector 1/30, name = con-1
Processing spacing values for connector 2/30, name = con-2
Processing spacing values for connector 3/30, name = con-3
Processing spacing values for connector 4/30, name = con-4
Processing spacing values for connector 5/30, name = con-5
Processing spacing values for connector 6/30, name = con-6
Processing spacing values for connector 7/30, name = con-7
Processing spacing values for connector 8/30, name = con-8
Processing spacing values for connector 9/30, name = con-9
Processing spacing values for connector 10/30, name = con-10
Processing spacing values for connector 11/30, name = con-11
Processing spacing values for connector 12/30, name = con-12
Processing spacing values for connector 13/30, name = con-13
Processing spacing values for connector 14/30, name = con-15
Processing spacing values for connector 15/30, name = con-16
Processing spacing values for connector 16/30, name = con-18
Processing spacing values for connector 17/30, name = con-19
Processing spacing values for connector 18/30, name = con-20
Processing spacing values for connector 19/30, name = con-21
Processing spacing values for connector 20/30, name = con-23
Processing spacing values for connector 21/30, name = con-24
Processing spacing values for connector 22/30, name = con-26
Processing spacing values for connector 23/30, name = con-27
Processing spacing values for connector 24/30, name = con-28
Processing spacing values for connector 25/30, name = con-29
Processing spacing values for connector 26/30, name = con-30
Processing spacing values for connector 27/30, name = con-31
Processing spacing values for connector 28/30, name = con-33
Processing spacing values for connector 29/30, name = con-35
Processing spacing values for connector 30/30, name = con-37
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/30, con-1.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 2/30, con-2.
Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10
Proximity test for connector 3/30, con-3.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 4/30, con-4.
Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333
Proximity test for connector 5/30, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 6/30, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 7/30, con-7.
Proximity test for connector 8/30, con-8.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 9/30, con-9.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 10/30, con-10.
Proximity test for connector 11/30, con-11.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 12/30, con-12.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 13/30, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 14/30, con-15.
Proximity test for connector 15/30, con-16.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 16/30, con-18.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/30, con-19.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 18/30, con-20.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 19/30, con-21.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 20/30, con-23.
Proximity test for connector 21/30, con-24.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 22/30, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 23/30, con-27.
Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905
Proximity test for connector 24/30, con-28.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 25/30, con-29.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 26/30, con-30.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 27/30, con-31.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 28/30, con-33.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 29/30, con-35.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Proximity test for connector 30/30, con-37.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 7
Connector con-2 current dim = 17
Connector con-3 current dim = 7
Connector con-4 current dim = 13
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 26
Connector con-9 current dim = 26
Connector con-10 current dim = 4
Connector con-11 current dim = 29
Connector con-12 current dim = 25
Connector con-13 current dim = 79
Connector con-15 current dim = 4
Connector con-16 current dim = 79
Connector con-18 current dim = 26
Connector con-19 current dim = 29
Connector con-20 current dim = 25
Connector con-21 current dim = 79
Connector con-23 current dim = 4
Connector con-24 current dim = 79
Connector con-26 current dim = 26
Connector con-27 current dim = 22
Connector con-28 current dim = 8
Connector con-29 current dim = 14
Connector con-30 current dim = 8
Connector con-31 current dim = 14
Connector con-33 current dim = 14
Connector con-35 current dim = 18
Connector con-37 current dim = 18
Domain list has 14 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 9.65124e-05
Number of periodic target domains = 0
Unstructured domain 1 of 14:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 2 of 14:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 3 of 14:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 4 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 5 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 6 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 7 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 10 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 11 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 12 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 13 of 14:
boundary name = Symmetry.
Creating boundary name Symmetry
Unstructured domain 14 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 14 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 14 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Creating T-Rex match boundary
Setting Push Attributes on Block.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.093673 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.079790 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 10094, numTets = 24500, (0.094447 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 11239, numTets = 31487, (0.084637 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 12325, numTets = 38114, (0.103827 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 13357, numTets = 44403, (0.099377 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 14324, numTets = 50295, (0.142690 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 15241, numTets = 55877, (0.123964 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 16110, numTets = 61157, (0.136756 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 16927, numTets = 66120, (0.115104 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 17688, numTets = 70732, (0.083173 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 18386, numTets = 74961, (0.070491 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 18989, numTets = 78621, (0.066730 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 19475, numTets = 81583, (0.060067 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 19803, numTets = 83573, (0.110746 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 19975, numTets = 84624, (0.029764 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 20038, numTets = 85011, (0.055958 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 20040, numTets = 85025, (0.031671 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 20040, numTets = 85025, (0.014975 seconds)
Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom)
Info: Average growth rate on match domains: 1.306535
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:52:33PM EDT
Run Time: 00 Hours 00 Minutes 12 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:52:33PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 90 / 90 curves to EGADS originals
GMA contains 30 edge groups
GMA contains 14 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:52:48PM EDT
Export Time: 00 Hours 00 Minutes 15 Seconds
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Number of command line arguments = 2
Sat Apr 06 2024 10:54:28PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 14 entries.
Quilt quilt-1: edge tolerance = 5e-07
Quilt quilt-2: edge tolerance = 8.32899e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 8.32899e-05
Quilt quilt-5: edge tolerance = 8.32899e-05
Quilt quilt-6: edge tolerance = 8.32899e-05
Quilt quilt-7: edge tolerance = 9.65124e-05
Quilt quilt-8: edge tolerance = 9.65124e-05
Quilt quilt-9: edge tolerance = 9.65124e-05
Quilt quilt-10: edge tolerance = 5e-07
Quilt quilt-11: edge tolerance = 5e-07
Quilt quilt-12: edge tolerance = 5e-07
Quilt quilt-13: edge tolerance = 9.65124e-05
Quilt quilt-14: edge tolerance = 5e-07
Maximum DB edge tolerance = 9.65124e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 14 entries.
Quilt list has 14 entries.
Original connector list has 30 entries.
Minimum connector length = 0.00316783
Tolerance = 9.65124e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 30 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-1
Max Edge Tol: 9.651e-05 on con-19
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/30, name = con-1
Changing dimension for connector 1/30 from 11 to 5
Checking dimension for connector 2/30, name = con-2
Checking dimension for connector 3/30, name = con-3
Changing dimension for connector 3/30 from 11 to 5
Checking dimension for connector 4/30, name = con-4
Checking dimension for connector 5/30, name = con-5
Changing dimension for connector 5/30 from 11 to 4
Checking dimension for connector 6/30, name = con-6
Changing dimension for connector 6/30 from 11 to 4
Checking dimension for connector 7/30, name = con-7
Changing dimension for connector 7/30 from 11 to 4
Checking dimension for connector 8/30, name = con-8
Changing dimension for connector 8/30 from 11 to 4
Checking dimension for connector 9/30, name = con-9
Changing dimension for connector 9/30 from 11 to 4
Checking dimension for connector 10/30, name = con-10
Changing dimension for connector 10/30 from 11 to 4
Checking dimension for connector 11/30, name = con-11
Checking dimension for connector 12/30, name = con-12
Changing dimension for connector 12/30 from 11 to 4
Checking dimension for connector 13/30, name = con-13
Checking dimension for connector 14/30, name = con-15
Changing dimension for connector 14/30 from 11 to 4
Checking dimension for connector 15/30, name = con-16
Checking dimension for connector 16/30, name = con-18
Changing dimension for connector 16/30 from 11 to 4
Checking dimension for connector 17/30, name = con-19
Checking dimension for connector 18/30, name = con-20
Changing dimension for connector 18/30 from 11 to 4
Checking dimension for connector 19/30, name = con-21
Checking dimension for connector 20/30, name = con-23
Changing dimension for connector 20/30 from 11 to 4
Checking dimension for connector 21/30, name = con-24
Checking dimension for connector 22/30, name = con-26
Changing dimension for connector 22/30 from 11 to 4
Checking dimension for connector 23/30, name = con-27
Checking dimension for connector 24/30, name = con-28
Changing dimension for connector 24/30 from 11 to 5
Checking dimension for connector 25/30, name = con-29
Checking dimension for connector 26/30, name = con-30
Changing dimension for connector 26/30 from 11 to 5
Checking dimension for connector 27/30, name = con-31
Checking dimension for connector 28/30, name = con-33
Checking dimension for connector 29/30, name = con-35
Checking dimension for connector 30/30, name = con-37
Processing spacing values for connector 1/30, name = con-1
Processing spacing values for connector 2/30, name = con-2
Processing spacing values for connector 3/30, name = con-3
Processing spacing values for connector 4/30, name = con-4
Processing spacing values for connector 5/30, name = con-5
Processing spacing values for connector 6/30, name = con-6
Processing spacing values for connector 7/30, name = con-7
Processing spacing values for connector 8/30, name = con-8
Processing spacing values for connector 9/30, name = con-9
Processing spacing values for connector 10/30, name = con-10
Processing spacing values for connector 11/30, name = con-11
Processing spacing values for connector 12/30, name = con-12
Processing spacing values for connector 13/30, name = con-13
Processing spacing values for connector 14/30, name = con-15
Processing spacing values for connector 15/30, name = con-16
Processing spacing values for connector 16/30, name = con-18
Processing spacing values for connector 17/30, name = con-19
Processing spacing values for connector 18/30, name = con-20
Processing spacing values for connector 19/30, name = con-21
Processing spacing values for connector 20/30, name = con-23
Processing spacing values for connector 21/30, name = con-24
Processing spacing values for connector 22/30, name = con-26
Processing spacing values for connector 23/30, name = con-27
Processing spacing values for connector 24/30, name = con-28
Processing spacing values for connector 25/30, name = con-29
Processing spacing values for connector 26/30, name = con-30
Processing spacing values for connector 27/30, name = con-31
Processing spacing values for connector 28/30, name = con-33
Processing spacing values for connector 29/30, name = con-35
Processing spacing values for connector 30/30, name = con-37
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/30, con-1.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 2/30, con-2.
Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10
Proximity test for connector 3/30, con-3.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 4/30, con-4.
Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333
Proximity test for connector 5/30, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 6/30, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 7/30, con-7.
Proximity test for connector 8/30, con-8.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 9/30, con-9.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 10/30, con-10.
Proximity test for connector 11/30, con-11.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 12/30, con-12.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 13/30, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 14/30, con-15.
Proximity test for connector 15/30, con-16.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 16/30, con-18.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/30, con-19.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 18/30, con-20.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 19/30, con-21.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 20/30, con-23.
Proximity test for connector 21/30, con-24.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 22/30, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 23/30, con-27.
Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905
Proximity test for connector 24/30, con-28.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 25/30, con-29.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 26/30, con-30.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 27/30, con-31.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 28/30, con-33.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 29/30, con-35.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Proximity test for connector 30/30, con-37.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 7
Connector con-2 current dim = 17
Connector con-3 current dim = 7
Connector con-4 current dim = 13
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 26
Connector con-9 current dim = 26
Connector con-10 current dim = 4
Connector con-11 current dim = 29
Connector con-12 current dim = 25
Connector con-13 current dim = 79
Connector con-15 current dim = 4
Connector con-16 current dim = 79
Connector con-18 current dim = 26
Connector con-19 current dim = 29
Connector con-20 current dim = 25
Connector con-21 current dim = 79
Connector con-23 current dim = 4
Connector con-24 current dim = 79
Connector con-26 current dim = 26
Connector con-27 current dim = 22
Connector con-28 current dim = 8
Connector con-29 current dim = 14
Connector con-30 current dim = 8
Connector con-31 current dim = 14
Connector con-33 current dim = 14
Connector con-35 current dim = 18
Connector con-37 current dim = 18
Domain list has 14 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 9.65124e-05
Number of periodic target domains = 0
Unstructured domain 1 of 14:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 2 of 14:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 3 of 14:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 4 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 5 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 6 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 7 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 10 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 11 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 12 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 13 of 14:
boundary name = Symmetry.
Creating boundary name Symmetry
Unstructured domain 14 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 14 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 14 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Creating T-Rex match boundary
Setting Push Attributes on Block.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.074304 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.129670 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 10092, numTets = 24488, (0.142405 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 11235, numTets = 31463, (0.122884 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 12319, numTets = 38078, (0.123759 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 13351, numTets = 44367, (0.121493 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 14318, numTets = 50259, (0.107142 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 15235, numTets = 55841, (0.122208 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 16104, numTets = 61121, (0.126540 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 16921, numTets = 66084, (0.117422 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 17682, numTets = 70696, (0.085418 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 18380, numTets = 74925, (0.063332 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 18983, numTets = 78585, (0.062783 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 19469, numTets = 81547, (0.066449 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 19797, numTets = 83537, (0.055876 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 19969, numTets = 84588, (0.028638 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 20032, numTets = 84975, (0.026386 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 20034, numTets = 84989, (0.046322 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 20034, numTets = 84989, (0.032801 seconds)
Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom)
Info: Average growth rate on match domains: 1.306535
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:54:42PM EDT
Run Time: 00 Hours 00 Minutes 14 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:54:42PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 90 / 90 curves to EGADS originals
GMA contains 30 edge groups
GMA contains 14 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:54:57PM EDT
Export Time: 00 Hours 00 Minutes 15 Seconds
Number of command line arguments = 2
Sat Apr 06 2024 10:55:08PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 14 entries.
Quilt quilt-1: edge tolerance = 5e-07
Quilt quilt-2: edge tolerance = 8.32899e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 8.32899e-05
Quilt quilt-5: edge tolerance = 8.32899e-05
Quilt quilt-6: edge tolerance = 8.32899e-05
Quilt quilt-7: edge tolerance = 9.65124e-05
Quilt quilt-8: edge tolerance = 9.65124e-05
Quilt quilt-9: edge tolerance = 9.65124e-05
Quilt quilt-10: edge tolerance = 5e-07
Quilt quilt-11: edge tolerance = 5e-07
Quilt quilt-12: edge tolerance = 5e-07
Quilt quilt-13: edge tolerance = 9.65124e-05
Quilt quilt-14: edge tolerance = 5e-07
Maximum DB edge tolerance = 9.65124e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 14 entries.
Quilt list has 14 entries.
Original connector list has 30 entries.
Minimum connector length = 0.00316783
Tolerance = 9.65124e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 30 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-1
Max Edge Tol: 9.651e-05 on con-19
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/30, name = con-1
Changing dimension for connector 1/30 from 11 to 5
Checking dimension for connector 2/30, name = con-2
Checking dimension for connector 3/30, name = con-3
Changing dimension for connector 3/30 from 11 to 5
Checking dimension for connector 4/30, name = con-4
Checking dimension for connector 5/30, name = con-5
Changing dimension for connector 5/30 from 11 to 4
Checking dimension for connector 6/30, name = con-6
Changing dimension for connector 6/30 from 11 to 4
Checking dimension for connector 7/30, name = con-7
Changing dimension for connector 7/30 from 11 to 4
Checking dimension for connector 8/30, name = con-8
Changing dimension for connector 8/30 from 11 to 4
Checking dimension for connector 9/30, name = con-9
Changing dimension for connector 9/30 from 11 to 4
Checking dimension for connector 10/30, name = con-10
Changing dimension for connector 10/30 from 11 to 4
Checking dimension for connector 11/30, name = con-11
Checking dimension for connector 12/30, name = con-12
Changing dimension for connector 12/30 from 11 to 4
Checking dimension for connector 13/30, name = con-13
Checking dimension for connector 14/30, name = con-15
Changing dimension for connector 14/30 from 11 to 4
Checking dimension for connector 15/30, name = con-16
Checking dimension for connector 16/30, name = con-18
Changing dimension for connector 16/30 from 11 to 4
Checking dimension for connector 17/30, name = con-19
Checking dimension for connector 18/30, name = con-20
Changing dimension for connector 18/30 from 11 to 4
Checking dimension for connector 19/30, name = con-21
Checking dimension for connector 20/30, name = con-23
Changing dimension for connector 20/30 from 11 to 4
Checking dimension for connector 21/30, name = con-24
Checking dimension for connector 22/30, name = con-26
Changing dimension for connector 22/30 from 11 to 4
Checking dimension for connector 23/30, name = con-27
Checking dimension for connector 24/30, name = con-28
Changing dimension for connector 24/30 from 11 to 5
Checking dimension for connector 25/30, name = con-29
Checking dimension for connector 26/30, name = con-30
Changing dimension for connector 26/30 from 11 to 5
Checking dimension for connector 27/30, name = con-31
Checking dimension for connector 28/30, name = con-33
Checking dimension for connector 29/30, name = con-35
Checking dimension for connector 30/30, name = con-37
Processing spacing values for connector 1/30, name = con-1
Processing spacing values for connector 2/30, name = con-2
Processing spacing values for connector 3/30, name = con-3
Processing spacing values for connector 4/30, name = con-4
Processing spacing values for connector 5/30, name = con-5
Processing spacing values for connector 6/30, name = con-6
Processing spacing values for connector 7/30, name = con-7
Processing spacing values for connector 8/30, name = con-8
Processing spacing values for connector 9/30, name = con-9
Processing spacing values for connector 10/30, name = con-10
Processing spacing values for connector 11/30, name = con-11
Processing spacing values for connector 12/30, name = con-12
Processing spacing values for connector 13/30, name = con-13
Processing spacing values for connector 14/30, name = con-15
Processing spacing values for connector 15/30, name = con-16
Processing spacing values for connector 16/30, name = con-18
Processing spacing values for connector 17/30, name = con-19
Processing spacing values for connector 18/30, name = con-20
Processing spacing values for connector 19/30, name = con-21
Processing spacing values for connector 20/30, name = con-23
Processing spacing values for connector 21/30, name = con-24
Processing spacing values for connector 22/30, name = con-26
Processing spacing values for connector 23/30, name = con-27
Processing spacing values for connector 24/30, name = con-28
Processing spacing values for connector 25/30, name = con-29
Processing spacing values for connector 26/30, name = con-30
Processing spacing values for connector 27/30, name = con-31
Processing spacing values for connector 28/30, name = con-33
Processing spacing values for connector 29/30, name = con-35
Processing spacing values for connector 30/30, name = con-37
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/30, con-1.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 2/30, con-2.
Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10
Proximity test for connector 3/30, con-3.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 4/30, con-4.
Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333
Proximity test for connector 5/30, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 6/30, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 7/30, con-7.
Proximity test for connector 8/30, con-8.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 9/30, con-9.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 10/30, con-10.
Proximity test for connector 11/30, con-11.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 12/30, con-12.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 13/30, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 14/30, con-15.
Proximity test for connector 15/30, con-16.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 16/30, con-18.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/30, con-19.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 18/30, con-20.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 19/30, con-21.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 20/30, con-23.
Proximity test for connector 21/30, con-24.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 22/30, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 23/30, con-27.
Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905
Proximity test for connector 24/30, con-28.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 25/30, con-29.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 26/30, con-30.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 27/30, con-31.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 28/30, con-33.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 29/30, con-35.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Proximity test for connector 30/30, con-37.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 7
Connector con-2 current dim = 17
Connector con-3 current dim = 7
Connector con-4 current dim = 13
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 26
Connector con-9 current dim = 26
Connector con-10 current dim = 4
Connector con-11 current dim = 29
Connector con-12 current dim = 25
Connector con-13 current dim = 79
Connector con-15 current dim = 4
Connector con-16 current dim = 79
Connector con-18 current dim = 26
Connector con-19 current dim = 29
Connector con-20 current dim = 25
Connector con-21 current dim = 79
Connector con-23 current dim = 4
Connector con-24 current dim = 79
Connector con-26 current dim = 26
Connector con-27 current dim = 22
Connector con-28 current dim = 8
Connector con-29 current dim = 14
Connector con-30 current dim = 8
Connector con-31 current dim = 14
Connector con-33 current dim = 14
Connector con-35 current dim = 18
Connector con-37 current dim = 18
Domain list has 14 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 9.65124e-05
Number of periodic target domains = 0
Unstructured domain 1 of 14:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 2 of 14:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 3 of 14:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 4 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 5 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 6 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 7 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 10 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 11 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 12 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 13 of 14:
boundary name = Symmetry.
Creating boundary name Symmetry
Unstructured domain 14 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 14 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 14 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Creating T-Rex match boundary
Setting Push Attributes on Block.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.105083 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.108977 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 10094, numTets = 24500, (0.080898 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 11239, numTets = 31487, (0.075713 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 12325, numTets = 38114, (0.069536 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 13357, numTets = 44403, (0.143716 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 14324, numTets = 50295, (0.070494 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 15241, numTets = 55877, (0.060797 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 16110, numTets = 61157, (0.059553 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 16927, numTets = 66120, (0.063822 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 17688, numTets = 70732, (0.066692 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 18386, numTets = 74961, (0.049379 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 18989, numTets = 78621, (0.058139 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 19475, numTets = 81583, (0.047686 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 19803, numTets = 83573, (0.037940 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 19975, numTets = 84624, (0.032653 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 20038, numTets = 85011, (0.025432 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 20040, numTets = 85025, (0.022913 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 20040, numTets = 85025, (0.014440 seconds)
Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom)
Info: Average growth rate on match domains: 1.306535
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:55:22PM EDT
Run Time: 00 Hours 00 Minutes 14 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:55:22PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 90 / 90 curves to EGADS originals
GMA contains 30 edge groups
GMA contains 14 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:55:36PM EDT
Export Time: 00 Hours 00 Minutes 14 Seconds
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Number of command line arguments = 2
Sat Apr 06 2024 10:56:43PM EDT
Fidelity Pointwise 2023.2
Loading user defaults from capsUserDefaults.glf
GeomToMesh: Defaults
Connector level
InitDim = 11
MaxDim = 1024
MinDim = 4
TurnAngle = 0.000000
Deviation = 0.000000
SplitAngle = 0.000000
JoinCons = 0
ProxGrowthRate = 1.300000
SourceSpacing = 0
TurnAngleHard = 70.000000
EqualSpacing = 0
Domain level
Algorithm = Delaunay
FullLayers = 0
MaxLayers = 0
GrowthRate = 1.300000
IsoType = Triangle
TRexType = Triangle
TRexARLimit = 200.000000
TRexAngleBC = 0.000000
Decay = 0.500000
MinEdge = 0.000000
MaxEdge = 0.000000
Adapt = 0
WallSpacing = 0.000000
StrDomConvertARTrigger = 0.000000
Block level
Algorithm = Delaunay
VoxelLayers = 3
boundaryDecay = 0.500000
collisionBuffer = 0.500000
maxSkewAngle = 180.000000
TRexSkewDelay = 0
edgeMaxGrowthRate = 1.800000
fullLayers = 1
maxLayers = 100
growthRate = 1.300000
TRexType = TetPyramid
volInitialize = 1
General
SkipMeshing = 1
CAESolver = UGRID
outerBoxScale = 0
sourceBoxLengthScale = 0.000000
sourceBoxDirection = 1.000000 0.000000 0.000000
sourceBoxAngle = 0.000000
sourceGrowthFactor = 10.000000
sourcePCDFile =
ModelSize = 0
writeGMA = 2.0
assembleTolMult = 2.0
modelOrientIntMeshVolume = 1
Elevate On Export
degree = Q1
costThreshold = 0.8
maxIncAngle = 175.0
relax = 0.05
smoothingPasses = 1000
WCNWeight = 0.5
WCNMode = Calculate
writeVTU = false
CADFile = caps.egads
Determining model size from file.
Info: Model Size adjusted to 100
Computing maximum DB edge tolerance.
Quilt list has 14 entries.
Quilt quilt-1: edge tolerance = 5e-07
Quilt quilt-2: edge tolerance = 8.32899e-05
Quilt quilt-3: edge tolerance = 6.19964e-05
Quilt quilt-4: edge tolerance = 8.32899e-05
Quilt quilt-5: edge tolerance = 8.32899e-05
Quilt quilt-6: edge tolerance = 8.32899e-05
Quilt quilt-7: edge tolerance = 9.65124e-05
Quilt quilt-8: edge tolerance = 9.65124e-05
Quilt quilt-9: edge tolerance = 9.65124e-05
Quilt quilt-10: edge tolerance = 5e-07
Quilt quilt-11: edge tolerance = 5e-07
Quilt quilt-12: edge tolerance = 5e-07
Quilt quilt-13: edge tolerance = 9.65124e-05
Quilt quilt-14: edge tolerance = 5e-07
Maximum DB edge tolerance = 9.65124e-05
Performing model assembly pass on geometry entities.
domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance
Looking for quilt names in geometry.
Quilt list has 14 entries.
Quilt list has 14 entries.
Original connector list has 30 entries.
Minimum connector length = 0.00316783
Tolerance = 9.65124e-05
Performing merge on connectors with equal dimensions and common end points.
After regular merge, connector list has 30 entries.
Updating conData
Min Edge Tol: 5.000e-07 on con-1
Max Edge Tol: 9.651e-05 on con-19
Adjusting connector dimensions based on average spacings.
Checking dimension for connector 1/30, name = con-1
Changing dimension for connector 1/30 from 11 to 5
Checking dimension for connector 2/30, name = con-2
Checking dimension for connector 3/30, name = con-3
Changing dimension for connector 3/30 from 11 to 5
Checking dimension for connector 4/30, name = con-4
Checking dimension for connector 5/30, name = con-5
Changing dimension for connector 5/30 from 11 to 4
Checking dimension for connector 6/30, name = con-6
Changing dimension for connector 6/30 from 11 to 4
Checking dimension for connector 7/30, name = con-7
Changing dimension for connector 7/30 from 11 to 4
Checking dimension for connector 8/30, name = con-8
Changing dimension for connector 8/30 from 11 to 4
Checking dimension for connector 9/30, name = con-9
Changing dimension for connector 9/30 from 11 to 4
Checking dimension for connector 10/30, name = con-10
Changing dimension for connector 10/30 from 11 to 4
Checking dimension for connector 11/30, name = con-11
Checking dimension for connector 12/30, name = con-12
Changing dimension for connector 12/30 from 11 to 4
Checking dimension for connector 13/30, name = con-13
Checking dimension for connector 14/30, name = con-15
Changing dimension for connector 14/30 from 11 to 4
Checking dimension for connector 15/30, name = con-16
Checking dimension for connector 16/30, name = con-18
Changing dimension for connector 16/30 from 11 to 4
Checking dimension for connector 17/30, name = con-19
Checking dimension for connector 18/30, name = con-20
Changing dimension for connector 18/30 from 11 to 4
Checking dimension for connector 19/30, name = con-21
Checking dimension for connector 20/30, name = con-23
Changing dimension for connector 20/30 from 11 to 4
Checking dimension for connector 21/30, name = con-24
Checking dimension for connector 22/30, name = con-26
Changing dimension for connector 22/30 from 11 to 4
Checking dimension for connector 23/30, name = con-27
Checking dimension for connector 24/30, name = con-28
Changing dimension for connector 24/30 from 11 to 5
Checking dimension for connector 25/30, name = con-29
Checking dimension for connector 26/30, name = con-30
Changing dimension for connector 26/30 from 11 to 5
Checking dimension for connector 27/30, name = con-31
Checking dimension for connector 28/30, name = con-33
Checking dimension for connector 29/30, name = con-35
Checking dimension for connector 30/30, name = con-37
Processing spacing values for connector 1/30, name = con-1
Processing spacing values for connector 2/30, name = con-2
Processing spacing values for connector 3/30, name = con-3
Processing spacing values for connector 4/30, name = con-4
Processing spacing values for connector 5/30, name = con-5
Processing spacing values for connector 6/30, name = con-6
Processing spacing values for connector 7/30, name = con-7
Processing spacing values for connector 8/30, name = con-8
Processing spacing values for connector 9/30, name = con-9
Processing spacing values for connector 10/30, name = con-10
Processing spacing values for connector 11/30, name = con-11
Processing spacing values for connector 12/30, name = con-12
Processing spacing values for connector 13/30, name = con-13
Processing spacing values for connector 14/30, name = con-15
Processing spacing values for connector 15/30, name = con-16
Processing spacing values for connector 16/30, name = con-18
Processing spacing values for connector 17/30, name = con-19
Processing spacing values for connector 18/30, name = con-20
Processing spacing values for connector 19/30, name = con-21
Processing spacing values for connector 20/30, name = con-23
Processing spacing values for connector 21/30, name = con-24
Processing spacing values for connector 22/30, name = con-26
Processing spacing values for connector 23/30, name = con-27
Processing spacing values for connector 24/30, name = con-28
Processing spacing values for connector 25/30, name = con-29
Processing spacing values for connector 26/30, name = con-30
Processing spacing values for connector 27/30, name = con-31
Processing spacing values for connector 28/30, name = con-33
Processing spacing values for connector 29/30, name = con-35
Processing spacing values for connector 30/30, name = con-37
Number of unique endpoints = 20
Checking for baffle intersections.
Performing Local Proximity Refinement
Adjusting connector dimensions based on proximity to other connectors.
Proximity test for connector 1/30, con-1.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 2/30, con-2.
Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10
Proximity test for connector 3/30, con-3.
Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333
Proximity test for connector 4/30, con-4.
Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333
Proximity test for connector 5/30, con-5.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 6/30, con-6.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277
Proximity test for connector 7/30, con-7.
Proximity test for connector 8/30, con-8.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 9/30, con-9.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185
Proximity test for connector 10/30, con-10.
Proximity test for connector 11/30, con-11.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656
Proximity test for connector 12/30, con-12.
Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526
Proximity test for connector 13/30, con-13.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214
Proximity test for connector 14/30, con-15.
Proximity test for connector 15/30, con-16.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212
Proximity test for connector 16/30, con-18.
Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571
Proximity test for connector 17/30, con-19.
Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639
Proximity test for connector 18/30, con-20.
Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381
Proximity test for connector 19/30, con-21.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036
Proximity test for connector 20/30, con-23.
Proximity test for connector 21/30, con-24.
Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031
Proximity test for connector 22/30, con-26.
Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643
Proximity test for connector 23/30, con-27.
Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905
Proximity test for connector 24/30, con-28.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 25/30, con-29.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 26/30, con-30.
Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286
Proximity test for connector 27/30, con-31.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 28/30, con-33.
Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077
Proximity test for connector 29/30, con-35.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Proximity test for connector 30/30, con-37.
Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176
Adjusting node spacing from geometry
Adjusting connector dimensions based on end spacings.
Connector con-1 current dim = 7
Connector con-2 current dim = 17
Connector con-3 current dim = 7
Connector con-4 current dim = 13
Connector con-5 current dim = 26
Connector con-6 current dim = 26
Connector con-7 current dim = 4
Connector con-8 current dim = 26
Connector con-9 current dim = 26
Connector con-10 current dim = 4
Connector con-11 current dim = 29
Connector con-12 current dim = 25
Connector con-13 current dim = 79
Connector con-15 current dim = 4
Connector con-16 current dim = 79
Connector con-18 current dim = 26
Connector con-19 current dim = 29
Connector con-20 current dim = 25
Connector con-21 current dim = 79
Connector con-23 current dim = 4
Connector con-24 current dim = 79
Connector con-26 current dim = 26
Connector con-27 current dim = 22
Connector con-28 current dim = 8
Connector con-29 current dim = 14
Connector con-30 current dim = 8
Connector con-31 current dim = 14
Connector con-33 current dim = 14
Connector con-35 current dim = 18
Connector con-37 current dim = 18
Domain list has 14 entries.
Looking for periodic domain attributes from geometry.
Tolerance = 9.65124e-05
Number of periodic target domains = 0
Unstructured domain 1 of 14:
boundary name = Farfield.
Creating boundary name Farfield
Unstructured domain 2 of 14:
boundary name = Wing2.
Creating boundary name Wing2
Unstructured domain 3 of 14:
boundary name = Wing1.
Creating boundary name Wing1
Unstructured domain 4 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 5 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 6 of 14:
boundary name = Wing2.
Wing2 already in boundary name list.
Unstructured domain 7 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 8 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 9 of 14:
boundary name = Wing1.
Wing1 already in boundary name list.
Unstructured domain 10 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 11 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 12 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Unstructured domain 13 of 14:
boundary name = Symmetry.
Creating boundary name Symmetry
Unstructured domain 14 of 14:
boundary name = Farfield.
Farfield already in boundary name list.
Checking for blunt flag attribute on geometry faces.
Performing initialization pass on all unstructured domains.
Unstructured domain list for assembly has 14 entries.
Structured domain list for assembly has 0 entries.
Periodic target domain list for assembly has 0 entries.
Creating unstructured block from 14 domains.
Block = auto-blk
Setting up unstructured block.
Retrieving block attributes from geometry.
Retrieving T-Rex volume boundary conditions from geometry.
Domain Wing2 has spacing value = 0.00282843.
Creating T-Rex wall boundary Wing2
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Domain Wing2 has spacing value = 0.00282843.
Looking for adjacent boundaries to set as match.
Creating T-Rex match boundary
Setting Push Attributes on Block.
Initializing unstructured block.
Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000
Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.148882 seconds)
Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000
Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.113416 seconds)
Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000
Info: End : aniso layer 3: numPts = 10094, numTets = 24500, (0.114044 seconds)
Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000
Info: End : aniso layer 4: numPts = 11239, numTets = 31487, (0.096047 seconds)
Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100
Info: End : aniso layer 5: numPts = 12325, numTets = 38114, (0.103817 seconds)
Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030
Info: End : aniso layer 6: numPts = 13357, numTets = 44403, (0.135763 seconds)
Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839
Info: End : aniso layer 7: numPts = 14324, numTets = 50295, (0.121978 seconds)
Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691
Info: End : aniso layer 8: numPts = 15241, numTets = 55877, (0.102031 seconds)
Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998
Info: End : aniso layer 9: numPts = 16110, numTets = 61157, (0.085100 seconds)
Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497
Info: End : aniso layer 10: numPts = 16927, numTets = 66120, (0.076081 seconds)
Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346
Info: End : aniso layer 11: numPts = 17688, numTets = 70732, (0.083505 seconds)
Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950
Info: End : aniso layer 12: numPts = 18386, numTets = 74961, (0.088386 seconds)
Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036
Info: End : aniso layer 13: numPts = 18989, numTets = 78621, (0.060653 seconds)
Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546
Info: End : aniso layer 14: numPts = 19475, numTets = 81583, (0.051863 seconds)
Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310
Info: End : aniso layer 15: numPts = 19803, numTets = 83573, (0.041634 seconds)
Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203
Info: End : aniso layer 16: numPts = 19975, numTets = 84624, (0.031485 seconds)
Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864
Info: End : aniso layer 17: numPts = 20038, numTets = 85011, (0.024386 seconds)
Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023
Info: End : aniso layer 18: numPts = 20040, numTets = 85025, (0.022281 seconds)
Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430
Info: End : aniso layer 19: numPts = 20040, numTets = 85025, (0.013322 seconds)
Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom)
Info: Average growth rate on match domains: 1.306535
CAE Solver set to UGRID
GeomToMesh finished!
Sat Apr 06 2024 10:56:57PM EDT
Run Time: 00 Hours 00 Minutes 14 Seconds
Pointwise save filename = caps.GeomToMesh.pw
Sat Apr 06 2024 10:56:57PM EDT
Exporting in UGRID format to file basename = caps.GeomToMesh
Mapped 90 / 90 curves to EGADS originals
GMA contains 30 edge groups
GMA contains 14 face groups
Wrote geometry-mesh associativity to caps.GeomToMesh.gma
GeomToMesh I/O finished!
Sat Apr 06 2024 10:57:11PM EDT
Export Time: 00 Hours 00 Minutes 14 Seconds
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Pointwise could not obtain a license:
ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows,
FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached.
Run 'lic_error LMF-02004' for more information.
Please check your license file, network, and license server status.
Volume mesh:
Number of nodes = 33598
Number of elements = 183094
Number of triangles = 13718
Number of quadrilatarals = 0
Number of tetrahedrals = 183094
Number of pyramids = 0
Number of prisms = 0
Number of hexahedrals = 0
Body = 1
Number of nodes = 6861
Number of elements = 13718
Number of tris = 13718
Number of quad = 0
Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_1.dat ....
Finished writing TECPLOT file
Writing TECPLOT file: pyCAPS_Pointwise_Test.dat ....
Finished writing TECPLOT file
WARNING: 'capsProblem.__init__' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsProblem.loadCAPS' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsGeometry.__init__' is deprecated. Please use 'Problem.__init__'!
WARNING: 'capsProblem.loadAIM' is deprecated. Please use 'Problem.analysis.create'!
WARNING: 'capsAnalysis.__init__' is deprecated. Please use 'Problem.analysis.create'!
WARNING: 'capsAnalysis.setAnalysisVal' is deprecated. Please use 'Analysis.input["varname"].value'!
WARNING: 'capsProblem.closeCAPS' is deprecated. Please use 'close'!
real 7m28.076s
user 2m16.151s
sys 0m22.159s
+ status=0
+ set +x
=================================================
Legacy CAPS verification (using pyCAPS) case pointwise_Symmetry_PyTest.py passed (as expected)
=================================================
*************************************************
*************************************************
All tests pass!
[Execution node] check if [reynolds] is in [[windows10x64]]
Run condition [Execution node ] preventing perform for step [Execute Windows batch command]
[GNU C Compiler (gcc)] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[GNU C Compiler (gcc)] Successfully parsed console log
[GNU C Compiler (gcc)] -> found 0 issues (skipped 0 duplicates)
[GNU C Compiler (gcc)] Skipping post processing
[GNU C Compiler (gcc)] No filter has been set, publishing all 0 issues
[GNU C Compiler (gcc)] Repository miner is not configured, skipping repository mining
[Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[Clang] -> found 0 issues (skipped 0 duplicates)
[Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[Clang] -> found 0 issues (skipped 0 duplicates)
[Clang] Successfully parsed console log
[Clang] -> found 0 issues (skipped 0 duplicates)
[Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[Clang] Skipping post processing
[Clang] No filter has been set, publishing all 0 issues
[Clang] Repository miner is not configured, skipping repository mining
[Static Analysis] Successfully parsed console log
[Static Analysis] -> found 0 issues (skipped 0 duplicates)
[Static Analysis] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[Static Analysis] Successfully parsed console log
[Static Analysis] -> found 0 issues (skipped 0 duplicates)
[Static Analysis] Skipping post processing
[Static Analysis] No filter has been set, publishing all 0 issues
[Static Analysis] Repository miner is not configured, skipping repository mining
[Static Analysis] Successfully parsed console log
[Static Analysis] -> found 0 issues (skipped 0 duplicates)
[Static Analysis] Successfully parsed console log
[Static Analysis] -> found 0 issues (skipped 0 duplicates)
[Static Analysis] Successfully parsed console log
[Static Analysis] -> found 0 issues (skipped 0 duplicates)
[Static Analysis] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64')
[Static Analysis] Skipping post processing
[Static Analysis] No filter has been set, publishing all 0 issues
[Static Analysis] Repository miner is not configured, skipping repository mining
[Static Analysis] Reference build recorder is not configured
[Static Analysis] No valid reference build found
[Static Analysis] All reported issues will be considered outstanding
[Static Analysis] No quality gates have been set - skipping
[Static Analysis] Health report is disabled - skipping
[Static Analysis] Created analysis result for 0 issues (found 0 new issues, fixed 0 issues)
[Static Analysis] Attaching ResultAction with ID 'analysis' to build 'ESP_RegCaps/CASREV=7.7,ESPTEST=CAPS/MESH,ESP_ARCH=LINUX64,buildnode=reynolds #631'.
[Checks API] No suitable checks publisher found.
[PostBuildScript] - [INFO] Executing post build scripts.
[PostBuildScript] - [INFO] build step #0 should only be executed on MATRIX
[WS-CLEANUP] Deleting project workspace...
[WS-CLEANUP] done
Finished: SUCCESS
![[Jenkins]](/csi/static/a404d988/images/svgs/logo.svg){kind=logo}
