The Jenkins Controller is preparing for shutdown. No new builds can be started.
Skipping 979 KB.. Full LogConnector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 21/32, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 22/32, con-27. Proximity test for connector 23/32, con-28. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 24/32, con-29. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 25/32, con-30. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 26/32, con-32. Proximity test for connector 27/32, con-33. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 28/32, con-36. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273 Proximity test for connector 29/32, con-37. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 30/32, con-40. Proximity test for connector 31/32, con-41. Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644 Proximity test for connector 32/32, con-42. Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 26 Connector con-2 current dim = 79 Connector con-3 current dim = 26 Connector con-4 current dim = 29 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 29 Connector con-9 current dim = 25 Connector con-10 current dim = 79 Connector con-12 current dim = 4 Connector con-13 current dim = 79 Connector con-16 current dim = 26 Connector con-17 current dim = 79 Connector con-20 current dim = 4 Connector con-21 current dim = 26 Connector con-22 current dim = 79 Connector con-23 current dim = 26 Connector con-24 current dim = 29 Connector con-25 current dim = 26 Connector con-26 current dim = 26 Connector con-27 current dim = 4 Connector con-28 current dim = 29 Connector con-29 current dim = 25 Connector con-30 current dim = 79 Connector con-32 current dim = 4 Connector con-33 current dim = 79 Connector con-36 current dim = 26 Connector con-37 current dim = 79 Connector con-40 current dim = 4 Connector con-41 current dim = 27 Connector con-42 current dim = 33 Domain list has 18 entries. Looking for periodic domain attributes from geometry. Tolerance = 8.32899e-05 Number of periodic target domains = 0 Unstructured domain 1 of 18: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 2 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 3 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 4 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 5 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 6 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 7 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 18: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 10 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 11 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 12 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 13 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 14 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 15 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 16 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 17 of 18: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 18 of 18: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 18 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 18 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.115264 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.179529 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 15023, numTets = 49198, (0.135490 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 17357, numTets = 63211, (0.150715 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 19572, numTets = 76519, (0.139589 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 21667, numTets = 89100, (0.142630 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 23641, numTets = 100953, (0.108544 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 25514, numTets = 112200, (0.102450 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 27292, numTets = 122878, (0.098838 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 28966, numTets = 132932, (0.091173 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 30526, numTets = 142298, (0.116630 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 31965, numTets = 150935, (0.117366 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 33232, numTets = 158562, (0.079203 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 34280, numTets = 164902, (0.068102 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 35025, numTets = 169416, (0.062948 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 35422, numTets = 171837, (0.040427 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 35553, numTets = 172637, (0.029241 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 35559, numTets = 172676, (0.023266 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 35559, numTets = 172676, (0.014353 seconds) CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:42:43PM EDT Run Time: 00 Hours 00 Minutes 11 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:42:43PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 96 / 96 curves to EGADS originals GMA contains 32 edge groups GMA contains 18 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:42:52PM EDT Export Time: 00 Hours 00 Minutes 09 Seconds Number of command line arguments = 2 Sat Apr 13 2024 10:43:03PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 18 entries. Quilt quilt-1: edge tolerance = 6.19964e-05 Quilt quilt-2: edge tolerance = 6.19964e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 6.19964e-05 Quilt quilt-5: edge tolerance = 6.19964e-05 Quilt quilt-6: edge tolerance = 6.19964e-05 Quilt quilt-7: edge tolerance = 6.19964e-05 Quilt quilt-8: edge tolerance = 6.19964e-05 Quilt quilt-9: edge tolerance = 8.32899e-05 Quilt quilt-10: edge tolerance = 8.32899e-05 Quilt quilt-11: edge tolerance = 8.32899e-05 Quilt quilt-12: edge tolerance = 8.32899e-05 Quilt quilt-13: edge tolerance = 8.32899e-05 Quilt quilt-14: edge tolerance = 8.32899e-05 Quilt quilt-15: edge tolerance = 8.32899e-05 Quilt quilt-16: edge tolerance = 8.32899e-05 Quilt quilt-17: edge tolerance = 6.19601e-06 Quilt quilt-18: edge tolerance = 6.19601e-06 Maximum DB edge tolerance = 8.32899e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.665798e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 18 entries. Quilt list has 18 entries. Original connector list has 32 entries. Minimum connector length = 0.00316783 Tolerance = 8.32899e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 32 entries. Updating conData Min Edge Tol: 5.000e-07 on con-12 Max Edge Tol: 8.329e-05 on con-25 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/32, name = con-1 Changing dimension for connector 1/32 from 11 to 4 Checking dimension for connector 2/32, name = con-2 Checking dimension for connector 3/32, name = con-3 Changing dimension for connector 3/32 from 11 to 4 Checking dimension for connector 4/32, name = con-4 Checking dimension for connector 5/32, name = con-5 Changing dimension for connector 5/32 from 11 to 4 Checking dimension for connector 6/32, name = con-6 Changing dimension for connector 6/32 from 11 to 4 Checking dimension for connector 7/32, name = con-7 Changing dimension for connector 7/32 from 11 to 4 Checking dimension for connector 8/32, name = con-8 Checking dimension for connector 9/32, name = con-9 Changing dimension for connector 9/32 from 11 to 4 Checking dimension for connector 10/32, name = con-10 Checking dimension for connector 11/32, name = con-12 Changing dimension for connector 11/32 from 11 to 4 Checking dimension for connector 12/32, name = con-13 Checking dimension for connector 13/32, name = con-16 Changing dimension for connector 13/32 from 11 to 4 Checking dimension for connector 14/32, name = con-17 Checking dimension for connector 15/32, name = con-20 Changing dimension for connector 15/32 from 11 to 4 Checking dimension for connector 16/32, name = con-21 Changing dimension for connector 16/32 from 11 to 4 Checking dimension for connector 17/32, name = con-22 Checking dimension for connector 18/32, name = con-23 Changing dimension for connector 18/32 from 11 to 4 Checking dimension for connector 19/32, name = con-24 Checking dimension for connector 20/32, name = con-25 Changing dimension for connector 20/32 from 11 to 4 Checking dimension for connector 21/32, name = con-26 Changing dimension for connector 21/32 from 11 to 4 Checking dimension for connector 22/32, name = con-27 Changing dimension for connector 22/32 from 11 to 4 Checking dimension for connector 23/32, name = con-28 Checking dimension for connector 24/32, name = con-29 Changing dimension for connector 24/32 from 11 to 4 Checking dimension for connector 25/32, name = con-30 Checking dimension for connector 26/32, name = con-32 Changing dimension for connector 26/32 from 11 to 4 Checking dimension for connector 27/32, name = con-33 Checking dimension for connector 28/32, name = con-36 Changing dimension for connector 28/32 from 11 to 4 Checking dimension for connector 29/32, name = con-37 Checking dimension for connector 30/32, name = con-40 Changing dimension for connector 30/32 from 11 to 4 Checking dimension for connector 31/32, name = con-41 Checking dimension for connector 32/32, name = con-42 Processing spacing values for connector 1/32, name = con-1 Processing spacing values for connector 2/32, name = con-2 Processing spacing values for connector 3/32, name = con-3 Processing spacing values for connector 4/32, name = con-4 Processing spacing values for connector 5/32, name = con-5 Processing spacing values for connector 6/32, name = con-6 Processing spacing values for connector 7/32, name = con-7 Processing spacing values for connector 8/32, name = con-8 Processing spacing values for connector 9/32, name = con-9 Processing spacing values for connector 10/32, name = con-10 Processing spacing values for connector 11/32, name = con-12 Processing spacing values for connector 12/32, name = con-13 Processing spacing values for connector 13/32, name = con-16 Processing spacing values for connector 14/32, name = con-17 Processing spacing values for connector 15/32, name = con-20 Processing spacing values for connector 16/32, name = con-21 Processing spacing values for connector 17/32, name = con-22 Processing spacing values for connector 18/32, name = con-23 Processing spacing values for connector 19/32, name = con-24 Processing spacing values for connector 20/32, name = con-25 Processing spacing values for connector 21/32, name = con-26 Processing spacing values for connector 22/32, name = con-27 Processing spacing values for connector 23/32, name = con-28 Processing spacing values for connector 24/32, name = con-29 Processing spacing values for connector 25/32, name = con-30 Processing spacing values for connector 26/32, name = con-32 Processing spacing values for connector 27/32, name = con-33 Processing spacing values for connector 28/32, name = con-36 Processing spacing values for connector 29/32, name = con-37 Processing spacing values for connector 30/32, name = con-40 Processing spacing values for connector 31/32, name = con-41 Processing spacing values for connector 32/32, name = con-42 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/32, con-1. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 2/32, con-2. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 3/32, con-3. Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183 Proximity test for connector 4/32, con-4. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 5/32, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 6/32, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 7/32, con-7. Proximity test for connector 8/32, con-8. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 9/32, con-9. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 10/32, con-10. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 11/32, con-12. Proximity test for connector 12/32, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 13/32, con-16. Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183 Proximity test for connector 14/32, con-17. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 15/32, con-20. Proximity test for connector 16/32, con-21. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/32, con-22. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 18/32, con-23. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273 Proximity test for connector 19/32, con-24. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 20/32, con-25. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 21/32, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 22/32, con-27. Proximity test for connector 23/32, con-28. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 24/32, con-29. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 25/32, con-30. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 26/32, con-32. Proximity test for connector 27/32, con-33. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 28/32, con-36. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273 Proximity test for connector 29/32, con-37. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 30/32, con-40. Proximity test for connector 31/32, con-41. Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644 Proximity test for connector 32/32, con-42. Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 26 Connector con-2 current dim = 79 Connector con-3 current dim = 26 Connector con-4 current dim = 29 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 29 Connector con-9 current dim = 25 Connector con-10 current dim = 79 Connector con-12 current dim = 4 Connector con-13 current dim = 79 Connector con-16 current dim = 26 Connector con-17 current dim = 79 Connector con-20 current dim = 4 Connector con-21 current dim = 26 Connector con-22 current dim = 79 Connector con-23 current dim = 26 Connector con-24 current dim = 29 Connector con-25 current dim = 26 Connector con-26 current dim = 26 Connector con-27 current dim = 4 Connector con-28 current dim = 29 Connector con-29 current dim = 25 Connector con-30 current dim = 79 Connector con-32 current dim = 4 Connector con-33 current dim = 79 Connector con-36 current dim = 26 Connector con-37 current dim = 79 Connector con-40 current dim = 4 Connector con-41 current dim = 27 Connector con-42 current dim = 33 Domain list has 18 entries. Looking for periodic domain attributes from geometry. Tolerance = 8.32899e-05 Number of periodic target domains = 0 Unstructured domain 1 of 18: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 2 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 3 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 4 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 5 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 6 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 7 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 18: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 10 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 11 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 12 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 13 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 14 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 15 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 16 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 17 of 18: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 18 of 18: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 18 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 18 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.118355 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.150749 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 15021, numTets = 49186, (0.124950 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 17355, numTets = 63199, (0.109040 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 19569, numTets = 76500, (0.104977 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 21664, numTets = 89081, (0.101129 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 23638, numTets = 100934, (0.100350 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 25511, numTets = 112181, (0.098011 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 27289, numTets = 122859, (0.087997 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 28963, numTets = 132913, (0.083790 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 30523, numTets = 142279, (0.079876 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 31962, numTets = 150916, (0.077433 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 33229, numTets = 158543, (0.066935 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 34277, numTets = 164883, (0.061024 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 35022, numTets = 169397, (0.048714 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 35419, numTets = 171818, (0.034677 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 35550, numTets = 172618, (0.030221 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 35556, numTets = 172657, (0.019169 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 35556, numTets = 172657, (0.014692 seconds) CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:43:13PM EDT Run Time: 00 Hours 00 Minutes 10 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:43:13PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 96 / 96 curves to EGADS originals GMA contains 32 edge groups GMA contains 18 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:43:22PM EDT Export Time: 00 Hours 00 Minutes 09 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Number of command line arguments = 2 Sat Apr 13 2024 10:43:55PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 18 entries. Quilt quilt-1: edge tolerance = 6.19964e-05 Quilt quilt-2: edge tolerance = 6.19964e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 6.19964e-05 Quilt quilt-5: edge tolerance = 6.19964e-05 Quilt quilt-6: edge tolerance = 6.19964e-05 Quilt quilt-7: edge tolerance = 6.19964e-05 Quilt quilt-8: edge tolerance = 6.19964e-05 Quilt quilt-9: edge tolerance = 8.32899e-05 Quilt quilt-10: edge tolerance = 8.32899e-05 Quilt quilt-11: edge tolerance = 8.32899e-05 Quilt quilt-12: edge tolerance = 8.32899e-05 Quilt quilt-13: edge tolerance = 8.32899e-05 Quilt quilt-14: edge tolerance = 8.32899e-05 Quilt quilt-15: edge tolerance = 8.32899e-05 Quilt quilt-16: edge tolerance = 8.32899e-05 Quilt quilt-17: edge tolerance = 6.19601e-06 Quilt quilt-18: edge tolerance = 6.19601e-06 Maximum DB edge tolerance = 8.32899e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.665798e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 18 entries. Quilt list has 18 entries. Original connector list has 32 entries. Minimum connector length = 0.00316783 Tolerance = 8.32899e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 32 entries. Updating conData Min Edge Tol: 5.000e-07 on con-12 Max Edge Tol: 8.329e-05 on con-25 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/32, name = con-1 Changing dimension for connector 1/32 from 11 to 4 Checking dimension for connector 2/32, name = con-2 Checking dimension for connector 3/32, name = con-3 Changing dimension for connector 3/32 from 11 to 4 Checking dimension for connector 4/32, name = con-4 Checking dimension for connector 5/32, name = con-5 Changing dimension for connector 5/32 from 11 to 4 Checking dimension for connector 6/32, name = con-6 Changing dimension for connector 6/32 from 11 to 4 Checking dimension for connector 7/32, name = con-7 Changing dimension for connector 7/32 from 11 to 4 Checking dimension for connector 8/32, name = con-8 Checking dimension for connector 9/32, name = con-9 Changing dimension for connector 9/32 from 11 to 4 Checking dimension for connector 10/32, name = con-10 Checking dimension for connector 11/32, name = con-12 Changing dimension for connector 11/32 from 11 to 4 Checking dimension for connector 12/32, name = con-13 Checking dimension for connector 13/32, name = con-16 Changing dimension for connector 13/32 from 11 to 4 Checking dimension for connector 14/32, name = con-17 Checking dimension for connector 15/32, name = con-20 Changing dimension for connector 15/32 from 11 to 4 Checking dimension for connector 16/32, name = con-21 Changing dimension for connector 16/32 from 11 to 4 Checking dimension for connector 17/32, name = con-22 Checking dimension for connector 18/32, name = con-23 Changing dimension for connector 18/32 from 11 to 4 Checking dimension for connector 19/32, name = con-24 Checking dimension for connector 20/32, name = con-25 Changing dimension for connector 20/32 from 11 to 4 Checking dimension for connector 21/32, name = con-26 Changing dimension for connector 21/32 from 11 to 4 Checking dimension for connector 22/32, name = con-27 Changing dimension for connector 22/32 from 11 to 4 Checking dimension for connector 23/32, name = con-28 Checking dimension for connector 24/32, name = con-29 Changing dimension for connector 24/32 from 11 to 4 Checking dimension for connector 25/32, name = con-30 Checking dimension for connector 26/32, name = con-32 Changing dimension for connector 26/32 from 11 to 4 Checking dimension for connector 27/32, name = con-33 Checking dimension for connector 28/32, name = con-36 Changing dimension for connector 28/32 from 11 to 4 Checking dimension for connector 29/32, name = con-37 Checking dimension for connector 30/32, name = con-40 Changing dimension for connector 30/32 from 11 to 4 Checking dimension for connector 31/32, name = con-41 Checking dimension for connector 32/32, name = con-42 Processing spacing values for connector 1/32, name = con-1 Processing spacing values for connector 2/32, name = con-2 Processing spacing values for connector 3/32, name = con-3 Processing spacing values for connector 4/32, name = con-4 Processing spacing values for connector 5/32, name = con-5 Processing spacing values for connector 6/32, name = con-6 Processing spacing values for connector 7/32, name = con-7 Processing spacing values for connector 8/32, name = con-8 Processing spacing values for connector 9/32, name = con-9 Processing spacing values for connector 10/32, name = con-10 Processing spacing values for connector 11/32, name = con-12 Processing spacing values for connector 12/32, name = con-13 Processing spacing values for connector 13/32, name = con-16 Processing spacing values for connector 14/32, name = con-17 Processing spacing values for connector 15/32, name = con-20 Processing spacing values for connector 16/32, name = con-21 Processing spacing values for connector 17/32, name = con-22 Processing spacing values for connector 18/32, name = con-23 Processing spacing values for connector 19/32, name = con-24 Processing spacing values for connector 20/32, name = con-25 Processing spacing values for connector 21/32, name = con-26 Processing spacing values for connector 22/32, name = con-27 Processing spacing values for connector 23/32, name = con-28 Processing spacing values for connector 24/32, name = con-29 Processing spacing values for connector 25/32, name = con-30 Processing spacing values for connector 26/32, name = con-32 Processing spacing values for connector 27/32, name = con-33 Processing spacing values for connector 28/32, name = con-36 Processing spacing values for connector 29/32, name = con-37 Processing spacing values for connector 30/32, name = con-40 Processing spacing values for connector 31/32, name = con-41 Processing spacing values for connector 32/32, name = con-42 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/32, con-1. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 2/32, con-2. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 3/32, con-3. Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183 Proximity test for connector 4/32, con-4. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 5/32, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 6/32, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 7/32, con-7. Proximity test for connector 8/32, con-8. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 9/32, con-9. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 10/32, con-10. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 11/32, con-12. Proximity test for connector 12/32, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 13/32, con-16. Connector dimension changed from 4 to 26, avg. spacing changed from 0.65682 to 0.0788183 Proximity test for connector 14/32, con-17. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 15/32, con-20. Proximity test for connector 16/32, con-21. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/32, con-22. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 18/32, con-23. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273 Proximity test for connector 19/32, con-24. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 20/32, con-25. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 21/32, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 22/32, con-27. Proximity test for connector 23/32, con-28. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 24/32, con-29. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 25/32, con-30. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 26/32, con-32. Proximity test for connector 27/32, con-33. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 28/32, con-36. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262728 to 0.0315273 Proximity test for connector 29/32, con-37. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 30/32, con-40. Proximity test for connector 31/32, con-41. Connector dimension changed from 11 to 27, avg. spacing changed from 25.1327 to 9.66644 Proximity test for connector 32/32, con-42. Connector dimension changed from 11 to 33, avg. spacing changed from 25.1327 to 7.85398 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 26 Connector con-2 current dim = 79 Connector con-3 current dim = 26 Connector con-4 current dim = 29 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 29 Connector con-9 current dim = 25 Connector con-10 current dim = 79 Connector con-12 current dim = 4 Connector con-13 current dim = 79 Connector con-16 current dim = 26 Connector con-17 current dim = 79 Connector con-20 current dim = 4 Connector con-21 current dim = 26 Connector con-22 current dim = 79 Connector con-23 current dim = 26 Connector con-24 current dim = 29 Connector con-25 current dim = 26 Connector con-26 current dim = 26 Connector con-27 current dim = 4 Connector con-28 current dim = 29 Connector con-29 current dim = 25 Connector con-30 current dim = 79 Connector con-32 current dim = 4 Connector con-33 current dim = 79 Connector con-36 current dim = 26 Connector con-37 current dim = 79 Connector con-40 current dim = 4 Connector con-41 current dim = 27 Connector con-42 current dim = 33 Domain list has 18 entries. Looking for periodic domain attributes from geometry. Tolerance = 8.32899e-05 Number of periodic target domains = 0 Unstructured domain 1 of 18: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 2 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 3 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 4 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 5 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 6 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 7 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 18: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 18: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 10 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 11 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 12 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 13 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 14 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 15 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 16 of 18: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 17 of 18: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 18 of 18: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 18 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 18 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 9650, numTets = 16938, (0.140154 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 12475, numTets = 33876, (0.150979 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 15024, numTets = 49206, (0.161156 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 17357, numTets = 63213, (0.150635 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 19571, numTets = 76514, (0.137425 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 21666, numTets = 89095, (0.120231 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 23640, numTets = 100948, (0.116312 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 25513, numTets = 112195, (0.114675 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 27291, numTets = 122873, (0.106910 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 28965, numTets = 132927, (0.146712 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 30525, numTets = 142293, (0.153426 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 31964, numTets = 150930, (0.131338 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 33231, numTets = 158557, (0.127520 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 34279, numTets = 164897, (0.095990 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 35024, numTets = 169411, (0.063720 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 35421, numTets = 171832, (0.061636 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 35552, numTets = 172632, (0.054800 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 35558, numTets = 172671, (0.053727 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 35558, numTets = 172671, (0.026482 seconds) CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:44:07PM EDT Run Time: 00 Hours 00 Minutes 12 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:44:07PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 96 / 96 curves to EGADS originals GMA contains 32 edge groups GMA contains 18 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:44:14PM EDT Export Time: 00 Hours 00 Minutes 07 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Volume mesh: Number of nodes = 59422 Number of elements = 340259 Number of triangles = 13638 Number of quadrilatarals = 0 Number of tetrahedrals = 340259 Number of pyramids = 0 Number of prisms = 0 Number of hexahedrals = 0 Body = 1 Number of nodes = 2848 Number of elements = 5692 Number of tris = 5692 Number of quad = 0 Body = 2 Number of nodes = 2825 Number of elements = 5646 Number of tris = 5646 Number of quad = 0 Body = 3 Number of nodes = 1152 Number of elements = 2300 Number of tris = 2300 Number of quad = 0 Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_1.dat .... Finished writing TECPLOT file Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_2.dat .... Finished writing TECPLOT file Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_3.dat .... Finished writing TECPLOT file Writing TECPLOT file: pyCAPS_Pointwise_Test.dat .... Finished writing TECPLOT file WARNING: 'capsProblem.__init__' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsProblem.loadCAPS' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsGeometry.__init__' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsProblem.loadAIM' is deprecated. Please use 'Problem.analysis.create'! WARNING: 'capsAnalysis.__init__' is deprecated. Please use 'Problem.analysis.create'! WARNING: 'capsAnalysis.setAnalysisVal' is deprecated. Please use 'Analysis.input["varname"].value'! WARNING: 'capsProblem.closeCAPS' is deprecated. Please use 'close'! real 12m41.420s user 10m47.099s sys 1m37.387s + status=0 + set +x ================================================= Legacy CAPS verification (using pyCAPS) case pointwise_PyTest.py passed (as expected) ================================================= ================================================= + rm -rf pointwise_Symmetry_PyTest + echo 'pointwise_Symmetry_PyTest.py test;' + tee -a /jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/regressionTest/pyCAPSlog.txt pointwise_Symmetry_PyTest.py test; + python -u pointwise_Symmetry_PyTest.py -verbosity=0 -workDir=runDirectory + tee -a /jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/regressionTest/pyCAPSlog.txt Mapping capsGroup attributes ................ Number of unique capsGroup attributes = 4 Name = Farfield, index = 1 Name = Symmetry, index = 2 Name = Wing1, index = 3 Name = Wing2, index = 4 Mapping capsMesh attributes ................ Number of unique capsMesh attributes = 4 Name = Farfield, index = 1 Name = Symmetry, index = 2 Name = Wing1, index = 3 Name = Wing2, index = 4 Getting mesh sizing parameters Mesh sizing name - Wing2 Done getting mesh sizing parameters Writing global Glyph inputs... Writing egads file '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64/CAPS/legacy/examples/pyCAPS/pointwise_Symmetry_PyTest/Scratch/runDirectory_PointwiseSymmetryAnalysisTest_pointwiseAIM/caps.egads'.... Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Number of command line arguments = 2 Sat Apr 13 2024 10:46:07PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 14 entries. Quilt quilt-1: edge tolerance = 5e-07 Quilt quilt-2: edge tolerance = 8.32899e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 8.32899e-05 Quilt quilt-5: edge tolerance = 8.32899e-05 Quilt quilt-6: edge tolerance = 8.32899e-05 Quilt quilt-7: edge tolerance = 9.65124e-05 Quilt quilt-8: edge tolerance = 9.65124e-05 Quilt quilt-9: edge tolerance = 9.65124e-05 Quilt quilt-10: edge tolerance = 5e-07 Quilt quilt-11: edge tolerance = 5e-07 Quilt quilt-12: edge tolerance = 5e-07 Quilt quilt-13: edge tolerance = 9.65124e-05 Quilt quilt-14: edge tolerance = 5e-07 Maximum DB edge tolerance = 9.65124e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 14 entries. Quilt list has 14 entries. Original connector list has 30 entries. Minimum connector length = 0.00316783 Tolerance = 9.65124e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 30 entries. Updating conData Min Edge Tol: 5.000e-07 on con-1 Max Edge Tol: 9.651e-05 on con-19 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/30, name = con-1 Changing dimension for connector 1/30 from 11 to 5 Checking dimension for connector 2/30, name = con-2 Checking dimension for connector 3/30, name = con-3 Changing dimension for connector 3/30 from 11 to 5 Checking dimension for connector 4/30, name = con-4 Checking dimension for connector 5/30, name = con-5 Changing dimension for connector 5/30 from 11 to 4 Checking dimension for connector 6/30, name = con-6 Changing dimension for connector 6/30 from 11 to 4 Checking dimension for connector 7/30, name = con-7 Changing dimension for connector 7/30 from 11 to 4 Checking dimension for connector 8/30, name = con-8 Changing dimension for connector 8/30 from 11 to 4 Checking dimension for connector 9/30, name = con-9 Changing dimension for connector 9/30 from 11 to 4 Checking dimension for connector 10/30, name = con-10 Changing dimension for connector 10/30 from 11 to 4 Checking dimension for connector 11/30, name = con-11 Checking dimension for connector 12/30, name = con-12 Changing dimension for connector 12/30 from 11 to 4 Checking dimension for connector 13/30, name = con-13 Checking dimension for connector 14/30, name = con-15 Changing dimension for connector 14/30 from 11 to 4 Checking dimension for connector 15/30, name = con-16 Checking dimension for connector 16/30, name = con-18 Changing dimension for connector 16/30 from 11 to 4 Checking dimension for connector 17/30, name = con-19 Checking dimension for connector 18/30, name = con-20 Changing dimension for connector 18/30 from 11 to 4 Checking dimension for connector 19/30, name = con-21 Checking dimension for connector 20/30, name = con-23 Changing dimension for connector 20/30 from 11 to 4 Checking dimension for connector 21/30, name = con-24 Checking dimension for connector 22/30, name = con-26 Changing dimension for connector 22/30 from 11 to 4 Checking dimension for connector 23/30, name = con-27 Checking dimension for connector 24/30, name = con-28 Changing dimension for connector 24/30 from 11 to 5 Checking dimension for connector 25/30, name = con-29 Checking dimension for connector 26/30, name = con-30 Changing dimension for connector 26/30 from 11 to 5 Checking dimension for connector 27/30, name = con-31 Checking dimension for connector 28/30, name = con-33 Checking dimension for connector 29/30, name = con-35 Checking dimension for connector 30/30, name = con-37 Processing spacing values for connector 1/30, name = con-1 Processing spacing values for connector 2/30, name = con-2 Processing spacing values for connector 3/30, name = con-3 Processing spacing values for connector 4/30, name = con-4 Processing spacing values for connector 5/30, name = con-5 Processing spacing values for connector 6/30, name = con-6 Processing spacing values for connector 7/30, name = con-7 Processing spacing values for connector 8/30, name = con-8 Processing spacing values for connector 9/30, name = con-9 Processing spacing values for connector 10/30, name = con-10 Processing spacing values for connector 11/30, name = con-11 Processing spacing values for connector 12/30, name = con-12 Processing spacing values for connector 13/30, name = con-13 Processing spacing values for connector 14/30, name = con-15 Processing spacing values for connector 15/30, name = con-16 Processing spacing values for connector 16/30, name = con-18 Processing spacing values for connector 17/30, name = con-19 Processing spacing values for connector 18/30, name = con-20 Processing spacing values for connector 19/30, name = con-21 Processing spacing values for connector 20/30, name = con-23 Processing spacing values for connector 21/30, name = con-24 Processing spacing values for connector 22/30, name = con-26 Processing spacing values for connector 23/30, name = con-27 Processing spacing values for connector 24/30, name = con-28 Processing spacing values for connector 25/30, name = con-29 Processing spacing values for connector 26/30, name = con-30 Processing spacing values for connector 27/30, name = con-31 Processing spacing values for connector 28/30, name = con-33 Processing spacing values for connector 29/30, name = con-35 Processing spacing values for connector 30/30, name = con-37 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/30, con-1. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 2/30, con-2. Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10 Proximity test for connector 3/30, con-3. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 4/30, con-4. Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333 Proximity test for connector 5/30, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 6/30, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 7/30, con-7. Proximity test for connector 8/30, con-8. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 9/30, con-9. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 10/30, con-10. Proximity test for connector 11/30, con-11. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 12/30, con-12. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 13/30, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 14/30, con-15. Proximity test for connector 15/30, con-16. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 16/30, con-18. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/30, con-19. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 18/30, con-20. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 19/30, con-21. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 20/30, con-23. Proximity test for connector 21/30, con-24. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 22/30, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 23/30, con-27. Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905 Proximity test for connector 24/30, con-28. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 25/30, con-29. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 26/30, con-30. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 27/30, con-31. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 28/30, con-33. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 29/30, con-35. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Proximity test for connector 30/30, con-37. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 7 Connector con-2 current dim = 17 Connector con-3 current dim = 7 Connector con-4 current dim = 13 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 26 Connector con-9 current dim = 26 Connector con-10 current dim = 4 Connector con-11 current dim = 29 Connector con-12 current dim = 25 Connector con-13 current dim = 79 Connector con-15 current dim = 4 Connector con-16 current dim = 79 Connector con-18 current dim = 26 Connector con-19 current dim = 29 Connector con-20 current dim = 25 Connector con-21 current dim = 79 Connector con-23 current dim = 4 Connector con-24 current dim = 79 Connector con-26 current dim = 26 Connector con-27 current dim = 22 Connector con-28 current dim = 8 Connector con-29 current dim = 14 Connector con-30 current dim = 8 Connector con-31 current dim = 14 Connector con-33 current dim = 14 Connector con-35 current dim = 18 Connector con-37 current dim = 18 Domain list has 14 entries. Looking for periodic domain attributes from geometry. Tolerance = 9.65124e-05 Number of periodic target domains = 0 Unstructured domain 1 of 14: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 2 of 14: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 3 of 14: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 4 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 5 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 6 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 7 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 10 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 11 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 12 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 13 of 14: boundary name = Symmetry. Creating boundary name Symmetry Unstructured domain 14 of 14: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 14 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 14 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Creating T-Rex match boundary Setting Push Attributes on Block. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.101658 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.116872 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 10093, numTets = 24494, (0.103775 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 11236, numTets = 31469, (0.097649 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 12320, numTets = 38084, (0.085008 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 13352, numTets = 44373, (0.065970 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 14319, numTets = 50265, (0.084746 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 15236, numTets = 55847, (0.084936 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 16105, numTets = 61127, (0.082139 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 16922, numTets = 66090, (0.087350 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 17683, numTets = 70702, (0.070448 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 18381, numTets = 74931, (0.066873 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 18984, numTets = 78591, (0.066014 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 19470, numTets = 81553, (0.056205 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 19798, numTets = 83543, (0.042448 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 19970, numTets = 84594, (0.031839 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 20033, numTets = 84981, (0.024287 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 20035, numTets = 84995, (0.020257 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 20035, numTets = 84995, (0.012630 seconds) Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom) Info: Average growth rate on match domains: 1.306535 CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:46:18PM EDT Run Time: 00 Hours 00 Minutes 11 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:46:18PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 90 / 90 curves to EGADS originals GMA contains 30 edge groups GMA contains 14 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:46:29PM EDT Export Time: 00 Hours 00 Minutes 11 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Number of command line arguments = 2 Sat Apr 13 2024 10:47:13PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 14 entries. Quilt quilt-1: edge tolerance = 5e-07 Quilt quilt-2: edge tolerance = 8.32899e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 8.32899e-05 Quilt quilt-5: edge tolerance = 8.32899e-05 Quilt quilt-6: edge tolerance = 8.32899e-05 Quilt quilt-7: edge tolerance = 9.65124e-05 Quilt quilt-8: edge tolerance = 9.65124e-05 Quilt quilt-9: edge tolerance = 9.65124e-05 Quilt quilt-10: edge tolerance = 5e-07 Quilt quilt-11: edge tolerance = 5e-07 Quilt quilt-12: edge tolerance = 5e-07 Quilt quilt-13: edge tolerance = 9.65124e-05 Quilt quilt-14: edge tolerance = 5e-07 Maximum DB edge tolerance = 9.65124e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 14 entries. Quilt list has 14 entries. Original connector list has 30 entries. Minimum connector length = 0.00316783 Tolerance = 9.65124e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 30 entries. Updating conData Min Edge Tol: 5.000e-07 on con-1 Max Edge Tol: 9.651e-05 on con-19 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/30, name = con-1 Changing dimension for connector 1/30 from 11 to 5 Checking dimension for connector 2/30, name = con-2 Checking dimension for connector 3/30, name = con-3 Changing dimension for connector 3/30 from 11 to 5 Checking dimension for connector 4/30, name = con-4 Checking dimension for connector 5/30, name = con-5 Changing dimension for connector 5/30 from 11 to 4 Checking dimension for connector 6/30, name = con-6 Changing dimension for connector 6/30 from 11 to 4 Checking dimension for connector 7/30, name = con-7 Changing dimension for connector 7/30 from 11 to 4 Checking dimension for connector 8/30, name = con-8 Changing dimension for connector 8/30 from 11 to 4 Checking dimension for connector 9/30, name = con-9 Changing dimension for connector 9/30 from 11 to 4 Checking dimension for connector 10/30, name = con-10 Changing dimension for connector 10/30 from 11 to 4 Checking dimension for connector 11/30, name = con-11 Checking dimension for connector 12/30, name = con-12 Changing dimension for connector 12/30 from 11 to 4 Checking dimension for connector 13/30, name = con-13 Checking dimension for connector 14/30, name = con-15 Changing dimension for connector 14/30 from 11 to 4 Checking dimension for connector 15/30, name = con-16 Checking dimension for connector 16/30, name = con-18 Changing dimension for connector 16/30 from 11 to 4 Checking dimension for connector 17/30, name = con-19 Checking dimension for connector 18/30, name = con-20 Changing dimension for connector 18/30 from 11 to 4 Checking dimension for connector 19/30, name = con-21 Checking dimension for connector 20/30, name = con-23 Changing dimension for connector 20/30 from 11 to 4 Checking dimension for connector 21/30, name = con-24 Checking dimension for connector 22/30, name = con-26 Changing dimension for connector 22/30 from 11 to 4 Checking dimension for connector 23/30, name = con-27 Checking dimension for connector 24/30, name = con-28 Changing dimension for connector 24/30 from 11 to 5 Checking dimension for connector 25/30, name = con-29 Checking dimension for connector 26/30, name = con-30 Changing dimension for connector 26/30 from 11 to 5 Checking dimension for connector 27/30, name = con-31 Checking dimension for connector 28/30, name = con-33 Checking dimension for connector 29/30, name = con-35 Checking dimension for connector 30/30, name = con-37 Processing spacing values for connector 1/30, name = con-1 Processing spacing values for connector 2/30, name = con-2 Processing spacing values for connector 3/30, name = con-3 Processing spacing values for connector 4/30, name = con-4 Processing spacing values for connector 5/30, name = con-5 Processing spacing values for connector 6/30, name = con-6 Processing spacing values for connector 7/30, name = con-7 Processing spacing values for connector 8/30, name = con-8 Processing spacing values for connector 9/30, name = con-9 Processing spacing values for connector 10/30, name = con-10 Processing spacing values for connector 11/30, name = con-11 Processing spacing values for connector 12/30, name = con-12 Processing spacing values for connector 13/30, name = con-13 Processing spacing values for connector 14/30, name = con-15 Processing spacing values for connector 15/30, name = con-16 Processing spacing values for connector 16/30, name = con-18 Processing spacing values for connector 17/30, name = con-19 Processing spacing values for connector 18/30, name = con-20 Processing spacing values for connector 19/30, name = con-21 Processing spacing values for connector 20/30, name = con-23 Processing spacing values for connector 21/30, name = con-24 Processing spacing values for connector 22/30, name = con-26 Processing spacing values for connector 23/30, name = con-27 Processing spacing values for connector 24/30, name = con-28 Processing spacing values for connector 25/30, name = con-29 Processing spacing values for connector 26/30, name = con-30 Processing spacing values for connector 27/30, name = con-31 Processing spacing values for connector 28/30, name = con-33 Processing spacing values for connector 29/30, name = con-35 Processing spacing values for connector 30/30, name = con-37 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/30, con-1. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 2/30, con-2. Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10 Proximity test for connector 3/30, con-3. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 4/30, con-4. Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333 Proximity test for connector 5/30, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 6/30, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 7/30, con-7. Proximity test for connector 8/30, con-8. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 9/30, con-9. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 10/30, con-10. Proximity test for connector 11/30, con-11. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 12/30, con-12. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 13/30, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 14/30, con-15. Proximity test for connector 15/30, con-16. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 16/30, con-18. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/30, con-19. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 18/30, con-20. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 19/30, con-21. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 20/30, con-23. Proximity test for connector 21/30, con-24. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 22/30, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 23/30, con-27. Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905 Proximity test for connector 24/30, con-28. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 25/30, con-29. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 26/30, con-30. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 27/30, con-31. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 28/30, con-33. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 29/30, con-35. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Proximity test for connector 30/30, con-37. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 7 Connector con-2 current dim = 17 Connector con-3 current dim = 7 Connector con-4 current dim = 13 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 26 Connector con-9 current dim = 26 Connector con-10 current dim = 4 Connector con-11 current dim = 29 Connector con-12 current dim = 25 Connector con-13 current dim = 79 Connector con-15 current dim = 4 Connector con-16 current dim = 79 Connector con-18 current dim = 26 Connector con-19 current dim = 29 Connector con-20 current dim = 25 Connector con-21 current dim = 79 Connector con-23 current dim = 4 Connector con-24 current dim = 79 Connector con-26 current dim = 26 Connector con-27 current dim = 22 Connector con-28 current dim = 8 Connector con-29 current dim = 14 Connector con-30 current dim = 8 Connector con-31 current dim = 14 Connector con-33 current dim = 14 Connector con-35 current dim = 18 Connector con-37 current dim = 18 Domain list has 14 entries. Looking for periodic domain attributes from geometry. Tolerance = 9.65124e-05 Number of periodic target domains = 0 Unstructured domain 1 of 14: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 2 of 14: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 3 of 14: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 4 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 5 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 6 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 7 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 10 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 11 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 12 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 13 of 14: boundary name = Symmetry. Creating boundary name Symmetry Unstructured domain 14 of 14: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 14 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 14 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Creating T-Rex match boundary Setting Push Attributes on Block. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.067166 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.078573 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 10093, numTets = 24494, (0.073298 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 11236, numTets = 31469, (0.072121 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 12320, numTets = 38084, (0.109223 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 13352, numTets = 44373, (0.132559 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 14319, numTets = 50265, (0.109093 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 15236, numTets = 55847, (0.099193 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 16105, numTets = 61127, (0.067698 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 16922, numTets = 66090, (0.079576 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 17683, numTets = 70702, (0.073509 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 18381, numTets = 74931, (0.072881 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 18984, numTets = 78591, (0.086847 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 19470, numTets = 81553, (0.057850 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 19798, numTets = 83543, (0.044580 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 19970, numTets = 84594, (0.034101 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 20033, numTets = 84981, (0.030111 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 20035, numTets = 84995, (0.022192 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 20035, numTets = 84995, (0.012640 seconds) Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom) Info: Average growth rate on match domains: 1.306535 CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:47:24PM EDT Run Time: 00 Hours 00 Minutes 11 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:47:24PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 90 / 90 curves to EGADS originals GMA contains 30 edge groups GMA contains 14 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:47:34PM EDT Export Time: 00 Hours 00 Minutes 10 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Number of command line arguments = 2 Sat Apr 13 2024 10:49:47PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 14 entries. Quilt quilt-1: edge tolerance = 5e-07 Quilt quilt-2: edge tolerance = 8.32899e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 8.32899e-05 Quilt quilt-5: edge tolerance = 8.32899e-05 Quilt quilt-6: edge tolerance = 8.32899e-05 Quilt quilt-7: edge tolerance = 9.65124e-05 Quilt quilt-8: edge tolerance = 9.65124e-05 Quilt quilt-9: edge tolerance = 9.65124e-05 Quilt quilt-10: edge tolerance = 5e-07 Quilt quilt-11: edge tolerance = 5e-07 Quilt quilt-12: edge tolerance = 5e-07 Quilt quilt-13: edge tolerance = 9.65124e-05 Quilt quilt-14: edge tolerance = 5e-07 Maximum DB edge tolerance = 9.65124e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 14 entries. Quilt list has 14 entries. Original connector list has 30 entries. Minimum connector length = 0.00316783 Tolerance = 9.65124e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 30 entries. Updating conData Min Edge Tol: 5.000e-07 on con-1 Max Edge Tol: 9.651e-05 on con-19 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/30, name = con-1 Changing dimension for connector 1/30 from 11 to 5 Checking dimension for connector 2/30, name = con-2 Checking dimension for connector 3/30, name = con-3 Changing dimension for connector 3/30 from 11 to 5 Checking dimension for connector 4/30, name = con-4 Checking dimension for connector 5/30, name = con-5 Changing dimension for connector 5/30 from 11 to 4 Checking dimension for connector 6/30, name = con-6 Changing dimension for connector 6/30 from 11 to 4 Checking dimension for connector 7/30, name = con-7 Changing dimension for connector 7/30 from 11 to 4 Checking dimension for connector 8/30, name = con-8 Changing dimension for connector 8/30 from 11 to 4 Checking dimension for connector 9/30, name = con-9 Changing dimension for connector 9/30 from 11 to 4 Checking dimension for connector 10/30, name = con-10 Changing dimension for connector 10/30 from 11 to 4 Checking dimension for connector 11/30, name = con-11 Checking dimension for connector 12/30, name = con-12 Changing dimension for connector 12/30 from 11 to 4 Checking dimension for connector 13/30, name = con-13 Checking dimension for connector 14/30, name = con-15 Changing dimension for connector 14/30 from 11 to 4 Checking dimension for connector 15/30, name = con-16 Checking dimension for connector 16/30, name = con-18 Changing dimension for connector 16/30 from 11 to 4 Checking dimension for connector 17/30, name = con-19 Checking dimension for connector 18/30, name = con-20 Changing dimension for connector 18/30 from 11 to 4 Checking dimension for connector 19/30, name = con-21 Checking dimension for connector 20/30, name = con-23 Changing dimension for connector 20/30 from 11 to 4 Checking dimension for connector 21/30, name = con-24 Checking dimension for connector 22/30, name = con-26 Changing dimension for connector 22/30 from 11 to 4 Checking dimension for connector 23/30, name = con-27 Checking dimension for connector 24/30, name = con-28 Changing dimension for connector 24/30 from 11 to 5 Checking dimension for connector 25/30, name = con-29 Checking dimension for connector 26/30, name = con-30 Changing dimension for connector 26/30 from 11 to 5 Checking dimension for connector 27/30, name = con-31 Checking dimension for connector 28/30, name = con-33 Checking dimension for connector 29/30, name = con-35 Checking dimension for connector 30/30, name = con-37 Processing spacing values for connector 1/30, name = con-1 Processing spacing values for connector 2/30, name = con-2 Processing spacing values for connector 3/30, name = con-3 Processing spacing values for connector 4/30, name = con-4 Processing spacing values for connector 5/30, name = con-5 Processing spacing values for connector 6/30, name = con-6 Processing spacing values for connector 7/30, name = con-7 Processing spacing values for connector 8/30, name = con-8 Processing spacing values for connector 9/30, name = con-9 Processing spacing values for connector 10/30, name = con-10 Processing spacing values for connector 11/30, name = con-11 Processing spacing values for connector 12/30, name = con-12 Processing spacing values for connector 13/30, name = con-13 Processing spacing values for connector 14/30, name = con-15 Processing spacing values for connector 15/30, name = con-16 Processing spacing values for connector 16/30, name = con-18 Processing spacing values for connector 17/30, name = con-19 Processing spacing values for connector 18/30, name = con-20 Processing spacing values for connector 19/30, name = con-21 Processing spacing values for connector 20/30, name = con-23 Processing spacing values for connector 21/30, name = con-24 Processing spacing values for connector 22/30, name = con-26 Processing spacing values for connector 23/30, name = con-27 Processing spacing values for connector 24/30, name = con-28 Processing spacing values for connector 25/30, name = con-29 Processing spacing values for connector 26/30, name = con-30 Processing spacing values for connector 27/30, name = con-31 Processing spacing values for connector 28/30, name = con-33 Processing spacing values for connector 29/30, name = con-35 Processing spacing values for connector 30/30, name = con-37 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/30, con-1. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 2/30, con-2. Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10 Proximity test for connector 3/30, con-3. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 4/30, con-4. Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333 Proximity test for connector 5/30, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 6/30, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 7/30, con-7. Proximity test for connector 8/30, con-8. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 9/30, con-9. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 10/30, con-10. Proximity test for connector 11/30, con-11. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 12/30, con-12. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 13/30, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 14/30, con-15. Proximity test for connector 15/30, con-16. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 16/30, con-18. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/30, con-19. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 18/30, con-20. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 19/30, con-21. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 20/30, con-23. Proximity test for connector 21/30, con-24. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 22/30, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 23/30, con-27. Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905 Proximity test for connector 24/30, con-28. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 25/30, con-29. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 26/30, con-30. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 27/30, con-31. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 28/30, con-33. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 29/30, con-35. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Proximity test for connector 30/30, con-37. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 7 Connector con-2 current dim = 17 Connector con-3 current dim = 7 Connector con-4 current dim = 13 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 26 Connector con-9 current dim = 26 Connector con-10 current dim = 4 Connector con-11 current dim = 29 Connector con-12 current dim = 25 Connector con-13 current dim = 79 Connector con-15 current dim = 4 Connector con-16 current dim = 79 Connector con-18 current dim = 26 Connector con-19 current dim = 29 Connector con-20 current dim = 25 Connector con-21 current dim = 79 Connector con-23 current dim = 4 Connector con-24 current dim = 79 Connector con-26 current dim = 26 Connector con-27 current dim = 22 Connector con-28 current dim = 8 Connector con-29 current dim = 14 Connector con-30 current dim = 8 Connector con-31 current dim = 14 Connector con-33 current dim = 14 Connector con-35 current dim = 18 Connector con-37 current dim = 18 Domain list has 14 entries. Looking for periodic domain attributes from geometry. Tolerance = 9.65124e-05 Number of periodic target domains = 0 Unstructured domain 1 of 14: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 2 of 14: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 3 of 14: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 4 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 5 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 6 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 7 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 10 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 11 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 12 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 13 of 14: boundary name = Symmetry. Creating boundary name Symmetry Unstructured domain 14 of 14: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 14 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 14 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Creating T-Rex match boundary Setting Push Attributes on Block. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.127897 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.121403 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 10093, numTets = 24494, (0.100459 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 11236, numTets = 31469, (0.071660 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 12320, numTets = 38084, (0.075792 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 13352, numTets = 44373, (0.075932 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 14319, numTets = 50265, (0.106071 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 15236, numTets = 55847, (0.109828 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 16105, numTets = 61127, (0.098872 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 16922, numTets = 66090, (0.116192 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 17683, numTets = 70702, (0.113017 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 18381, numTets = 74931, (0.087510 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 18984, numTets = 78591, (0.080738 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 19470, numTets = 81553, (0.100444 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 19798, numTets = 83543, (0.061068 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 19970, numTets = 84594, (0.049275 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 20033, numTets = 84981, (0.048742 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 20035, numTets = 84995, (0.044658 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 20035, numTets = 84995, (0.035529 seconds) Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom) Info: Average growth rate on match domains: 1.306535 CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:50:02PM EDT Run Time: 00 Hours 00 Minutes 15 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:50:02PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 90 / 90 curves to EGADS originals GMA contains 30 edge groups GMA contains 14 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:50:15PM EDT Export Time: 00 Hours 00 Minutes 13 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Number of command line arguments = 2 Sat Apr 13 2024 10:50:49PM EDT Fidelity Pointwise 2023.2 Loading user defaults from capsUserDefaults.glf GeomToMesh: Defaults Connector level InitDim = 11 MaxDim = 1024 MinDim = 4 TurnAngle = 0.000000 Deviation = 0.000000 SplitAngle = 0.000000 JoinCons = 0 ProxGrowthRate = 1.300000 SourceSpacing = 0 TurnAngleHard = 70.000000 EqualSpacing = 0 Domain level Algorithm = Delaunay FullLayers = 0 MaxLayers = 0 GrowthRate = 1.300000 IsoType = Triangle TRexType = Triangle TRexARLimit = 200.000000 TRexAngleBC = 0.000000 Decay = 0.500000 MinEdge = 0.000000 MaxEdge = 0.000000 Adapt = 0 WallSpacing = 0.000000 StrDomConvertARTrigger = 0.000000 Block level Algorithm = Delaunay VoxelLayers = 3 boundaryDecay = 0.500000 collisionBuffer = 0.500000 maxSkewAngle = 180.000000 TRexSkewDelay = 0 edgeMaxGrowthRate = 1.800000 fullLayers = 1 maxLayers = 100 growthRate = 1.300000 TRexType = TetPyramid volInitialize = 1 General SkipMeshing = 1 CAESolver = UGRID outerBoxScale = 0 sourceBoxLengthScale = 0.000000 sourceBoxDirection = 1.000000 0.000000 0.000000 sourceBoxAngle = 0.000000 sourceGrowthFactor = 10.000000 sourcePCDFile = ModelSize = 0 writeGMA = 2.0 assembleTolMult = 2.0 modelOrientIntMeshVolume = 1 Elevate On Export degree = Q1 costThreshold = 0.8 maxIncAngle = 175.0 relax = 0.05 smoothingPasses = 1000 WCNWeight = 0.5 WCNMode = Calculate writeVTU = false CADFile = caps.egads Determining model size from file. Info: Model Size adjusted to 100 Computing maximum DB edge tolerance. Quilt list has 14 entries. Quilt quilt-1: edge tolerance = 5e-07 Quilt quilt-2: edge tolerance = 8.32899e-05 Quilt quilt-3: edge tolerance = 6.19964e-05 Quilt quilt-4: edge tolerance = 8.32899e-05 Quilt quilt-5: edge tolerance = 8.32899e-05 Quilt quilt-6: edge tolerance = 8.32899e-05 Quilt quilt-7: edge tolerance = 9.65124e-05 Quilt quilt-8: edge tolerance = 9.65124e-05 Quilt quilt-9: edge tolerance = 9.65124e-05 Quilt quilt-10: edge tolerance = 5e-07 Quilt quilt-11: edge tolerance = 5e-07 Quilt quilt-12: edge tolerance = 5e-07 Quilt quilt-13: edge tolerance = 9.65124e-05 Quilt quilt-14: edge tolerance = 5e-07 Maximum DB edge tolerance = 9.65124e-05 Performing model assembly pass on geometry entities. domParams(MinEdge) defined as 1.930247e-04 due to model assembly tolerance Looking for quilt names in geometry. Quilt list has 14 entries. Quilt list has 14 entries. Original connector list has 30 entries. Minimum connector length = 0.00316783 Tolerance = 9.65124e-05 Performing merge on connectors with equal dimensions and common end points. After regular merge, connector list has 30 entries. Updating conData Min Edge Tol: 5.000e-07 on con-1 Max Edge Tol: 9.651e-05 on con-19 Adjusting connector dimensions based on average spacings. Checking dimension for connector 1/30, name = con-1 Changing dimension for connector 1/30 from 11 to 5 Checking dimension for connector 2/30, name = con-2 Checking dimension for connector 3/30, name = con-3 Changing dimension for connector 3/30 from 11 to 5 Checking dimension for connector 4/30, name = con-4 Checking dimension for connector 5/30, name = con-5 Changing dimension for connector 5/30 from 11 to 4 Checking dimension for connector 6/30, name = con-6 Changing dimension for connector 6/30 from 11 to 4 Checking dimension for connector 7/30, name = con-7 Changing dimension for connector 7/30 from 11 to 4 Checking dimension for connector 8/30, name = con-8 Changing dimension for connector 8/30 from 11 to 4 Checking dimension for connector 9/30, name = con-9 Changing dimension for connector 9/30 from 11 to 4 Checking dimension for connector 10/30, name = con-10 Changing dimension for connector 10/30 from 11 to 4 Checking dimension for connector 11/30, name = con-11 Checking dimension for connector 12/30, name = con-12 Changing dimension for connector 12/30 from 11 to 4 Checking dimension for connector 13/30, name = con-13 Checking dimension for connector 14/30, name = con-15 Changing dimension for connector 14/30 from 11 to 4 Checking dimension for connector 15/30, name = con-16 Checking dimension for connector 16/30, name = con-18 Changing dimension for connector 16/30 from 11 to 4 Checking dimension for connector 17/30, name = con-19 Checking dimension for connector 18/30, name = con-20 Changing dimension for connector 18/30 from 11 to 4 Checking dimension for connector 19/30, name = con-21 Checking dimension for connector 20/30, name = con-23 Changing dimension for connector 20/30 from 11 to 4 Checking dimension for connector 21/30, name = con-24 Checking dimension for connector 22/30, name = con-26 Changing dimension for connector 22/30 from 11 to 4 Checking dimension for connector 23/30, name = con-27 Checking dimension for connector 24/30, name = con-28 Changing dimension for connector 24/30 from 11 to 5 Checking dimension for connector 25/30, name = con-29 Checking dimension for connector 26/30, name = con-30 Changing dimension for connector 26/30 from 11 to 5 Checking dimension for connector 27/30, name = con-31 Checking dimension for connector 28/30, name = con-33 Checking dimension for connector 29/30, name = con-35 Checking dimension for connector 30/30, name = con-37 Processing spacing values for connector 1/30, name = con-1 Processing spacing values for connector 2/30, name = con-2 Processing spacing values for connector 3/30, name = con-3 Processing spacing values for connector 4/30, name = con-4 Processing spacing values for connector 5/30, name = con-5 Processing spacing values for connector 6/30, name = con-6 Processing spacing values for connector 7/30, name = con-7 Processing spacing values for connector 8/30, name = con-8 Processing spacing values for connector 9/30, name = con-9 Processing spacing values for connector 10/30, name = con-10 Processing spacing values for connector 11/30, name = con-11 Processing spacing values for connector 12/30, name = con-12 Processing spacing values for connector 13/30, name = con-13 Processing spacing values for connector 14/30, name = con-15 Processing spacing values for connector 15/30, name = con-16 Processing spacing values for connector 16/30, name = con-18 Processing spacing values for connector 17/30, name = con-19 Processing spacing values for connector 18/30, name = con-20 Processing spacing values for connector 19/30, name = con-21 Processing spacing values for connector 20/30, name = con-23 Processing spacing values for connector 21/30, name = con-24 Processing spacing values for connector 22/30, name = con-26 Processing spacing values for connector 23/30, name = con-27 Processing spacing values for connector 24/30, name = con-28 Processing spacing values for connector 25/30, name = con-29 Processing spacing values for connector 26/30, name = con-30 Processing spacing values for connector 27/30, name = con-31 Processing spacing values for connector 28/30, name = con-33 Processing spacing values for connector 29/30, name = con-35 Processing spacing values for connector 30/30, name = con-37 Number of unique endpoints = 20 Checking for baffle intersections. Performing Local Proximity Refinement Adjusting connector dimensions based on proximity to other connectors. Proximity test for connector 1/30, con-1. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 2/30, con-2. Connector dimension changed from 11 to 17, avg. spacing changed from 16 to 10 Proximity test for connector 3/30, con-3. Connector dimension changed from 5 to 7, avg. spacing changed from 20 to 13.3333 Proximity test for connector 4/30, con-4. Connector dimension changed from 11 to 13, avg. spacing changed from 16 to 13.3333 Proximity test for connector 5/30, con-5. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 6/30, con-6. Connector dimension changed from 4 to 26, avg. spacing changed from 0.262731 to 0.0315277 Proximity test for connector 7/30, con-7. Proximity test for connector 8/30, con-8. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 9/30, con-9. Connector dimension changed from 4 to 26, avg. spacing changed from 0.656821 to 0.0788185 Proximity test for connector 10/30, con-10. Proximity test for connector 11/30, con-11. Connector dimension changed from 11 to 29, avg. spacing changed from 0.326636 to 0.116656 Proximity test for connector 12/30, con-12. Connector dimension changed from 4 to 25, avg. spacing changed from 0.506821 to 0.0633526 Proximity test for connector 13/30, con-13. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295787 to 0.0379214 Proximity test for connector 14/30, con-15. Proximity test for connector 15/30, con-16. Connector dimension changed from 11 to 79, avg. spacing changed from 0.295786 to 0.0379212 Proximity test for connector 16/30, con-18. Connector dimension changed from 4 to 26, avg. spacing changed from 0.535476 to 0.0642571 Proximity test for connector 17/30, con-19. Connector dimension changed from 11 to 29, avg. spacing changed from 0.81659 to 0.291639 Proximity test for connector 18/30, con-20. Connector dimension changed from 4 to 25, avg. spacing changed from 1.26705 to 0.158381 Proximity test for connector 19/30, con-21. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739468 to 0.0948036 Proximity test for connector 20/30, con-23. Proximity test for connector 21/30, con-24. Connector dimension changed from 11 to 79, avg. spacing changed from 0.739464 to 0.0948031 Proximity test for connector 22/30, con-26. Connector dimension changed from 4 to 26, avg. spacing changed from 1.33869 to 0.160643 Proximity test for connector 23/30, con-27. Connector dimension changed from 11 to 22, avg. spacing changed from 16 to 7.61905 Proximity test for connector 24/30, con-28. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 25/30, con-29. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 26/30, con-30. Connector dimension changed from 5 to 8, avg. spacing changed from 20 to 11.4286 Proximity test for connector 27/30, con-31. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 28/30, con-33. Connector dimension changed from 11 to 14, avg. spacing changed from 16 to 12.3077 Proximity test for connector 29/30, con-35. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Proximity test for connector 30/30, con-37. Connector dimension changed from 11 to 18, avg. spacing changed from 16 to 9.41176 Adjusting node spacing from geometry Adjusting connector dimensions based on end spacings. Connector con-1 current dim = 7 Connector con-2 current dim = 17 Connector con-3 current dim = 7 Connector con-4 current dim = 13 Connector con-5 current dim = 26 Connector con-6 current dim = 26 Connector con-7 current dim = 4 Connector con-8 current dim = 26 Connector con-9 current dim = 26 Connector con-10 current dim = 4 Connector con-11 current dim = 29 Connector con-12 current dim = 25 Connector con-13 current dim = 79 Connector con-15 current dim = 4 Connector con-16 current dim = 79 Connector con-18 current dim = 26 Connector con-19 current dim = 29 Connector con-20 current dim = 25 Connector con-21 current dim = 79 Connector con-23 current dim = 4 Connector con-24 current dim = 79 Connector con-26 current dim = 26 Connector con-27 current dim = 22 Connector con-28 current dim = 8 Connector con-29 current dim = 14 Connector con-30 current dim = 8 Connector con-31 current dim = 14 Connector con-33 current dim = 14 Connector con-35 current dim = 18 Connector con-37 current dim = 18 Domain list has 14 entries. Looking for periodic domain attributes from geometry. Tolerance = 9.65124e-05 Number of periodic target domains = 0 Unstructured domain 1 of 14: boundary name = Farfield. Creating boundary name Farfield Unstructured domain 2 of 14: boundary name = Wing2. Creating boundary name Wing2 Unstructured domain 3 of 14: boundary name = Wing1. Creating boundary name Wing1 Unstructured domain 4 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 5 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 6 of 14: boundary name = Wing2. Wing2 already in boundary name list. Unstructured domain 7 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 8 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 9 of 14: boundary name = Wing1. Wing1 already in boundary name list. Unstructured domain 10 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 11 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 12 of 14: boundary name = Farfield. Farfield already in boundary name list. Unstructured domain 13 of 14: boundary name = Symmetry. Creating boundary name Symmetry Unstructured domain 14 of 14: boundary name = Farfield. Farfield already in boundary name list. Checking for blunt flag attribute on geometry faces. Performing initialization pass on all unstructured domains. Unstructured domain list for assembly has 14 entries. Structured domain list for assembly has 0 entries. Periodic target domain list for assembly has 0 entries. Creating unstructured block from 14 domains. Block = auto-blk Setting up unstructured block. Retrieving block attributes from geometry. Retrieving T-Rex volume boundary conditions from geometry. Domain Wing2 has spacing value = 0.00282843. Creating T-Rex wall boundary Wing2 Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Domain Wing2 has spacing value = 0.00282843. Looking for adjacent boundaries to set as match. Creating T-Rex match boundary Setting Push Attributes on Block. Initializing unstructured block. Info: Begin: aniso layer 1: growthRate = 1.000000, height = 1.000000, totalHeight = 1.000000 Info: End : aniso layer 1: numPts = 7462, numTets = 8461, (0.113525 seconds) Info: Begin: aniso layer 2: growthRate = 1.300000, height = 1.300000, totalHeight = 2.300000 Info: End : aniso layer 2: numPts = 8840, numTets = 16846, (0.117552 seconds) Info: Begin: aniso layer 3: growthRate = 1.300000, height = 1.690000, totalHeight = 3.990000 Info: End : aniso layer 3: numPts = 10094, numTets = 24500, (0.123978 seconds) Info: Begin: aniso layer 4: growthRate = 1.300000, height = 2.197000, totalHeight = 6.187000 Info: End : aniso layer 4: numPts = 11239, numTets = 31487, (0.099664 seconds) Info: Begin: aniso layer 5: growthRate = 1.300000, height = 2.856100, totalHeight = 9.043100 Info: End : aniso layer 5: numPts = 12325, numTets = 38114, (0.107027 seconds) Info: Begin: aniso layer 6: growthRate = 1.300000, height = 3.712930, totalHeight = 12.756030 Info: End : aniso layer 6: numPts = 13357, numTets = 44403, (0.101315 seconds) Info: Begin: aniso layer 7: growthRate = 1.300000, height = 4.826809, totalHeight = 17.582839 Info: End : aniso layer 7: numPts = 14324, numTets = 50295, (0.096646 seconds) Info: Begin: aniso layer 8: growthRate = 1.300000, height = 6.274852, totalHeight = 23.857691 Info: End : aniso layer 8: numPts = 15241, numTets = 55877, (0.090955 seconds) Info: Begin: aniso layer 9: growthRate = 1.300000, height = 8.157307, totalHeight = 32.014998 Info: End : aniso layer 9: numPts = 16110, numTets = 61157, (0.088076 seconds) Info: Begin: aniso layer 10: growthRate = 1.300000, height = 10.604499, totalHeight = 42.619497 Info: End : aniso layer 10: numPts = 16927, numTets = 66120, (0.089455 seconds) Info: Begin: aniso layer 11: growthRate = 1.300000, height = 13.785849, totalHeight = 56.405346 Info: End : aniso layer 11: numPts = 17688, numTets = 70732, (0.097119 seconds) Info: Begin: aniso layer 12: growthRate = 1.300000, height = 17.921604, totalHeight = 74.326950 Info: End : aniso layer 12: numPts = 18386, numTets = 74961, (0.081532 seconds) Info: Begin: aniso layer 13: growthRate = 1.300000, height = 23.298085, totalHeight = 97.625036 Info: End : aniso layer 13: numPts = 18989, numTets = 78621, (0.099670 seconds) Info: Begin: aniso layer 14: growthRate = 1.300000, height = 30.287511, totalHeight = 127.912546 Info: End : aniso layer 14: numPts = 19475, numTets = 81583, (0.081807 seconds) Info: Begin: aniso layer 15: growthRate = 1.300000, height = 39.373764, totalHeight = 167.286310 Info: End : aniso layer 15: numPts = 19803, numTets = 83573, (0.045648 seconds) Info: Begin: aniso layer 16: growthRate = 1.300000, height = 51.185893, totalHeight = 218.472203 Info: End : aniso layer 16: numPts = 19975, numTets = 84624, (0.058141 seconds) Info: Begin: aniso layer 17: growthRate = 1.300000, height = 66.541661, totalHeight = 285.013864 Info: End : aniso layer 17: numPts = 20038, numTets = 85011, (0.025769 seconds) Info: Begin: aniso layer 18: growthRate = 1.300000, height = 86.504159, totalHeight = 371.518023 Info: End : aniso layer 18: numPts = 20040, numTets = 85025, (0.025857 seconds) Info: Begin: aniso layer 19: growthRate = 1.300000, height = 112.455407, totalHeight = 483.973430 Info: End : aniso layer 19: numPts = 20040, numTets = 85025, (0.014259 seconds) Warning: Domains that are not adjacent to growth BCs are not eligible for match cell replacement: (quilt-1-dom), (quilt-11-dom), (quilt-10-dom), (quilt-12-dom), (quilt-7-dom), (quilt-3-dom), (quilt-8-dom), (quilt-9-dom), (quilt-14-dom) Info: Average growth rate on match domains: 1.306535 CAE Solver set to UGRID GeomToMesh finished! Sat Apr 13 2024 10:51:04PM EDT Run Time: 00 Hours 00 Minutes 15 Seconds Pointwise save filename = caps.GeomToMesh.pw Sat Apr 13 2024 10:51:04PM EDT Exporting in UGRID format to file basename = caps.GeomToMesh Mapped 90 / 90 curves to EGADS originals GMA contains 30 edge groups GMA contains 14 face groups Wrote geometry-mesh associativity to caps.GeomToMesh.gma GeomToMesh I/O finished! Sat Apr 13 2024 10:51:17PM EDT Export Time: 00 Hours 00 Minutes 13 Seconds Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Pointwise could not obtain a license: ERROR (LMF-02004): License call failed for feature fidelity_pointwise, version 23.100 and quantity 1. The license server search path is defined as 5280@acdl.mit.edu. The FLEXnet error message is as follows, FLEXnet ERROR(-4, 0, 0): Licensed number of users already reached. Run 'lic_error LMF-02004' for more information. Please check your license file, network, and license server status. Volume mesh: Number of nodes = 33663 Number of elements = 183456 Number of triangles = 13718 Number of quadrilatarals = 0 Number of tetrahedrals = 183456 Number of pyramids = 0 Number of prisms = 0 Number of hexahedrals = 0 Body = 1 Number of nodes = 6861 Number of elements = 13718 Number of tris = 13718 Number of quad = 0 Writing TECPLOT file: pyCAPS_Pointwise_Test_Surf_1.dat .... Finished writing TECPLOT file Writing TECPLOT file: pyCAPS_Pointwise_Test.dat .... Finished writing TECPLOT file WARNING: 'capsProblem.__init__' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsProblem.loadCAPS' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsGeometry.__init__' is deprecated. Please use 'Problem.__init__'! WARNING: 'capsProblem.loadAIM' is deprecated. Please use 'Problem.analysis.create'! WARNING: 'capsAnalysis.__init__' is deprecated. Please use 'Problem.analysis.create'! WARNING: 'capsAnalysis.setAnalysisVal' is deprecated. Please use 'Analysis.input["varname"].value'! WARNING: 'capsProblem.closeCAPS' is deprecated. Please use 'close'! real 7m14.123s user 2m13.684s sys 0m24.737s + status=0 + set +x ================================================= Legacy CAPS verification (using pyCAPS) case pointwise_Symmetry_PyTest.py passed (as expected) ================================================= ************************************************* ************************************************* All tests pass! [Execution node] check if [reynolds] is in [[windows10x64]] Run condition [Execution node ] preventing perform for step [Execute Windows batch command] [GNU C Compiler (gcc)] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [GNU C Compiler (gcc)] Successfully parsed console log [GNU C Compiler (gcc)] -> found 0 issues (skipped 0 duplicates) [GNU C Compiler (gcc)] Skipping post processing [GNU C Compiler (gcc)] No filter has been set, publishing all 0 issues [GNU C Compiler (gcc)] Repository miner is not configured, skipping repository mining [Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [Clang] -> found 0 issues (skipped 0 duplicates) [Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [Clang] -> found 0 issues (skipped 0 duplicates) [Clang] Successfully parsed console log [Clang] -> found 0 issues (skipped 0 duplicates) [Clang] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [Clang] Skipping post processing [Clang] No filter has been set, publishing all 0 issues [Clang] Repository miner is not configured, skipping repository mining [Static Analysis] Successfully parsed console log [Static Analysis] -> found 0 issues (skipped 0 duplicates) [Static Analysis] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [Static Analysis] Successfully parsed console log [Static Analysis] -> found 0 issues (skipped 0 duplicates) [Static Analysis] Skipping post processing [Static Analysis] No filter has been set, publishing all 0 issues [Static Analysis] Repository miner is not configured, skipping repository mining [Static Analysis] Successfully parsed console log [Static Analysis] -> found 0 issues (skipped 0 duplicates) [Static Analysis] Successfully parsed console log [Static Analysis] -> found 0 issues (skipped 0 duplicates) [Static Analysis] Successfully parsed console log [Static Analysis] -> found 0 issues (skipped 0 duplicates) [Static Analysis] Parsing console log (workspace: '/jenkins/workspace/ESP_RegCaps/7.7/CAPS/MESH/LINUX64') [Static Analysis] Skipping post processing [Static Analysis] No filter has been set, publishing all 0 issues [Static Analysis] Repository miner is not configured, skipping repository mining [Static Analysis] Reference build recorder is not configured [Static Analysis] No valid reference build found [Static Analysis] All reported issues will be considered outstanding [Static Analysis] No quality gates have been set - skipping [Static Analysis] Health report is disabled - skipping [Static Analysis] Created analysis result for 0 issues (found 0 new issues, fixed 0 issues) [Static Analysis] Attaching ResultAction with ID 'analysis' to build 'ESP_RegCaps/CASREV=7.7,ESPTEST=CAPS/MESH,ESP_ARCH=LINUX64,buildnode=reynolds #634'. [Checks API] No suitable checks publisher found. [PostBuildScript] - [INFO] Executing post build scripts. [PostBuildScript] - [INFO] build step #0 should only be executed on MATRIX [WS-CLEANUP] Deleting project workspace... [WS-CLEANUP] done Finished: SUCCESS